Bucket-brigade chorus with EQ, 1989 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Boss CH-1 Super Chorus.
An MN3007 delay chip holds a copy of the guitar about 4 ms behind, and a slow triangle swings that delay through the MN3101 clock. EQ cuts the copy’s treble and E.Level sets how loud it comes into the mix at output A. Output B carries the dry signal.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC1a lifts the treble about 15 dB, and mixer IC5b cuts it back down, so the delay chip’s hiss comes down with it. Two 3 V zeners across IC1a hold its output under about 3.4 V peak on a hard pick. The wet side has a three-pole low-pass before the chip and another after it, so the clock’s steps stay out of the output. At half Depth the clock runs 114 to 148 kHz, a delay of 3.5 to 4.5 ms. At full Depth it runs 110 to 166 kHz, 3.1 to 4.65 ms. Rate runs the sweep from about 0.26 to 4.4 times a second. EQ and C35 cut the copy’s treble, from about 530 Hz at LO to above the audio band at HI. E.Level sets the copy’s level against the dry signal, from about 0.16 to 1.2 times. The footswitch and its electronic bypass are left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C34, 100 µF electrolytic
- Bulk cap across the 9 V supply.
- R24, 33 kΩ
- Feeds Q7’s base. With C12 it smooths the base voltage.
- C12, 10 µF electrolytic
- Holds Q7’s base steady, so the 8 V line carries much less ripple and clock noise.
- Q7, 2SC1815
- Emitter follower that makes the 8 V line for the whole circuit. A 2SC1685, modeled as a 2SC1815.
- C11, 100 µF electrolytic
- Filters the 8 V line.
- R48, 10 kΩ
- Top of the bias divider (marked +4.5 V on the drawing).
- R51, 10 kΩ
- Bottom of the bias divider.
- C23, 47 µF electrolytic
- Filters the bias line.
- R42, 10 kΩ
- Top of the LFO’s bias divider.
- R47, 10 kΩ
- Bottom of the LFO’s bias divider.
- C24, 47 µF electrolytic
- Filters the LFO’s bias line.
- R1, 1 kΩ
- In series with the input.
- C1, 47 nF
- Input coupling cap.
- R2, 1 MΩ
- Biases the buffer’s input and sets the input impedance at 1 MΩ.
- IC1b, RC4558
- Input buffer, a follower. Its output is the dry signal: it goes straight to output B and into IC1a. Half an M5218L, modeled as a 4558.
- C32, 470 nF electrolytic
- Couples the buffer into the pre-emphasis stage.
- R3, 47 kΩ
- Input resistor of the pre-emphasis stage. Against R5 it sets a gain of 1 for low notes.
- C31, 6.8 nF
- With R4 beside R3 it lifts the treble. The lift starts near 410 Hz and levels off near 2.3 kHz, about 15 dB up.
- R4, 10 kΩ
- In series with C31. It sets where the treble lift levels off.
- R5, 47 kΩ
- Feedback resistor of the pre-emphasis stage.
- C30, 100 pF
- Rolls the top end off above about 34 kHz.
- D3, D4, 2.7 V zener pair, one direction, one each way
- Two 3 V zeners back to back (RD3.0EB1) across the feedback. They hold the stage’s output under about 3.4 V peak, so a hard pick doesn’t overload the delay chip. Modeled as the bench’s 2.7 V zener pair.
- R6, 10 kΩ
- Biases the + input from the bias line.
- IC1a, RC4558
- Pre-emphasis stage, inverting. Treble goes up about 15 dB before the delay so the chip’s hiss can come down the same amount after it. Its output feeds the delay side and, as the dry signal, mixer A. Half an M5218L.
- C29, 33 nF
- Couples the signal into the delay side. With R10 it cuts below about 48 Hz.
- R10, 100 kΩ
- Holds the filter’s input on the bias line.
- R7, 10 kΩ
- In series ahead of the low-pass.
- C2, 470 pF
- First cap of the low-pass.
- R8, 10 kΩ
- Low-pass filter resistor.
- C4, 1.8 nF
- Feedback cap from Q3’s emitter. It squares up the low-pass’s knee.
- R9, 10 kΩ
- Low-pass filter resistor.
- C5, 220 pF
- Last cap of the low-pass. With C2, C4 and the 10 kΩ resistors it makes a three-pole low-pass near 20 kHz, so the clock doesn’t fold high notes back down.
- Q3, 2SC2240-GR
- Emitter follower of the low-pass. It drives the delay chip. A 2SC2240.
- R12, 10 kΩ
- Q3’s emitter load.
- C6, 10 µF electrolytic
- Couples the signal into the delay chip.
- R13, 4.7 kΩ
- Into the delay chip’s input.
- R17, 8.2 kΩ
- Top of the divider that biases the delay chip’s input.
- R16, 1 kΩ
- Middle of that divider.
- R15, 10 kΩ
- Bottom of that divider.
- C7, 10 µF electrolytic
- Filters the divider.
- R14, 100 kΩ
- Brings the divider’s DC, about 4.6 V, to the delay chip’s input. The CH-1 has no bias trimmer.
- IC2, MN3007
- MN3007 delay line, 1024 stages. It holds 512 samples and passes each on after 512 clock periods, a few milliseconds here. Its supply pins run from ground to the 8 V line. The two outputs are drawn as one pin.
- R31, 56 kΩ
- Load on the delay chip’s outputs, to the 8 V line.
- C21, 33 nF
- Couples the delayed signal into the second low-pass.
- R38, 330 kΩ
- Holds the second filter’s input on the bias line.
- R32, 10 kΩ
- First resistor of the low-pass after the chip.
- C20, 470 pF
- First cap of the second low-pass.
- R37, 10 kΩ
- Low-pass filter resistor.
- C18, 1.8 nF
- Feedback cap from Q10’s emitter.
- R33, 10 kΩ
- Low-pass filter resistor.
- C19, 220 pF
- Last cap of the second low-pass, the same as the first. It smooths the chip’s steps.
- Q10, 2SC2240-GR
- Emitter follower of the second low-pass. A 2SC2240.
- R34, 10 kΩ
- Q10’s emitter load.
- R59, 1 kΩ
- In series ahead of EQ.
- EQ, 250 kΩ pot, reverse audio taper
- EQ, 250 kΩ reverse audio, used as a variable resistor. With C35 it is a treble cut on the wet signal only. Toward HI there is less resistance and the cut moves up, from about 530 Hz at LO to above the audio band at HI, about 5.3 kHz at half.
- C35, 1.2 nF
- The EQ’s cap. With EQ it sets where the wet signal’s treble starts to fall.
- C39, 33 nF
- Couples the EQ into IC5a.
- R55, 1 MΩ
- Biases IC5a’s input from the bias line.
- IC5a, RC4558
- Buffer after the EQ, a follower. Half an M5218L.
- E.Level, 250 kΩ pot, reverse audio taper
- E.Level, 250 kΩ reverse audio, used as a variable resistor in series with R50. It sets how loud the wet signal comes into mixer A, about 0.16 to 1.2 times the dry signal’s gain.
- C40, 10 µF electrolytic
- Couples the wet signal toward mixer A.
- R49, 1 MΩ
- Holds the wet line on the bias line.
- R50, 39 kΩ
- Wet signal into mixer A. The JFET switch Q2 after it is drawn as a wire, since it is on with the effect on.
- C28, 10 µF electrolytic
- Couples the dry signal into mixer A.
- R52, 1 MΩ
- Holds the dry line on the bias line.
- R53, 47 kΩ
- Dry signal into mixer A. The JFET switch Q1 after it is drawn as a wire.
- IC5b, RC4558
- Mixer A and de-emphasis. It adds the dry and wet signals and cuts the treble back down by the 15 dB IC1a added. Half an M5218L.
- R56, 47 kΩ
- Feedback resistor of mixer A. Against R53 the dry signal comes through at a gain of 1 for low notes.
- C37, 100 pF
- Rolls the top end off above about 34 kHz.
- C38, 6.8 nF
- With R57 beside R56 it cuts the treble by the same curve the pre-emphasis raised it.
- R57, 10 kΩ
- In series with C38.
- C36, 1 µF electrolytic
- Output A coupling cap.
- R54, 100 kΩ
- Holds output A at 0 V so the jack doesn’t pop.
- R60, 1 kΩ
- In series with output A.
- C33, 1 µF electrolytic
- Output B coupling cap. Output B carries the dry signal from IC1b.
- R61, 100 kΩ
- Holds output B at 0 V.
- R62, 1 kΩ
- In series with output B. Nothing is plugged into output B on the bench.
- IC4b, RC4558
- Comparator with hysteresis, which means it switches at one level on the way up and a different one on the way down. Its output flips to the other rail each time the triangle reaches a peak, so it puts out a square wave. Half an M5223L, modeled as a 4558.
- R45, 33 kΩ
- From the triangle to the comparator. Against R43 it sets the triangle’s height at about 0.7 of the square’s.
- R43, 47 kΩ
- Positive feedback that holds the comparator where it last flipped.
- C25, 10 nF
- From the square to the − input. It slows each flip slightly.
- R44, 100 kΩ
- Holds the comparator’s − input on the LFO’s bias line.
- Rate, 250 kΩ pot, reverse audio taper
- Rate, 250 kΩ reverse audio, used as a variable resistor in series with R46. Turned up, its resistance drops and the triangle ramps faster.
- R46, 15 kΩ
- Integrator input resistor. It sets the fastest sweep.
- C26, 10 µF electrolytic
- Integrator cap, one of two 10 µF in series, back to back, so together they act as one 5 µF cap that works either way round.
- C27, 10 µF electrolytic
- The second integrator cap.
- IC4a, RC4558
- Integrator. The square wave in makes a triangle out. Half an M5223L.
- Depth, 100 kΩ pot, linear taper
- Depth, 100 kΩ linear. It sets how much of the triangle reaches the clock, and that sets how far the delay swings. At 0 the delay holds still.
- R18, 220 kΩ
- With C9 it rounds the triangle’s corners (about 72 Hz).
- C9, 10 nF
- Smoothing cap on Q5’s base.
- Q5, 2SC1815
- Emitter follower for the LFO. A 2SC1685, modeled as a 2SC1815.
- R20, 4.7 kΩ
- Top of a divider that halves Q5’s emitter voltage.
- R19, 4.7 kΩ
- Bottom of that divider.
- D6, 1N914 / 1N4148
- Feeds the LFO into the clock’s timing node. The higher the LFO voltage, the more current it adds, so the clock runs faster and the delay gets shorter. 1N4148.
- RCV, 56 kΩ
- Stand-in, not on the pedal. It sizes the LFO’s pull on the model clock, as on the bench’s CE-2 and CE-3.
- R22, 150 kΩ
- Timing resistor. It charges C10 and sets the slowest clock, with the LFO at the bottom of its swing.
- IC3, MN3101
- MN3101 clock. Its timing cap C10 is 47 pF. More current into the timing pin runs the clock faster. Q6, D7, R21 and R23, which empty C10 each cycle, are part of the clock and not drawn.
About this version
- As drawn
- Negative ground, 9 V. Q7 filters the battery into an 8 V line for the whole circuit. The audio works around the 4 V from R48 and R51, marked +4.5 V on the drawing.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.