Op-amp overdrive with three diodes in the feedback, 1982 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Ampeg A-3 Overdrive.
An emitter follower, an op-amp clipping stage with two diodes one way and one the other across its feedback, an inverting stage with a gain of one, then a passive tone control, Level and an emitter follower out.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC1A’s gain is 1 plus 10 kΩ and the Overdrive pot over 4.7 kΩ, from about 3 to about 220. The 1 µF in series with the 4.7 kΩ keeps the gain at 1 below about 34 Hz. Across the feedback, D2 and D3 in series face one way and D1 faces the other. The wave swings about 0.6 V past the clean signal on one side and about 1.2 V on the other, so the clipping is uneven. U1B inverts the signal at a gain of 1 and trims the treble from about 16 kHz. Tone fades between a treble path through C8 and a darker path through R13 and C9. The model leaves out the bypass switching.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R18, 33 kΩ
- Top of the 4.5 V reference divider.
- R19, 33 kΩ
- Bottom of the reference divider.
- C13, 47 µF electrolytic
- Filters the 4.5 V reference.
- R1, 1 kΩ
- Input series resistor.
- C1, 47 nF
- Input coupling cap.
- R2, 470 kΩ
- Biases Q1’s base at 4.5 V and sets the input impedance near 470 kΩ.
- Q1, 2SC1815
- Input buffer, an emitter follower.
- R3, 10 kΩ
- Q1’s emitter resistor.
- C3, 1 µF
- Coupling cap toward the clipping stage.
- R4, 100 kΩ
- Holds the JFET switch’s input side at 4.5 V. The switch is drawn as a wire.
- R5, 1 MΩ
- Holds the JFET switch’s output side at 4.5 V.
- C4, 1 µF
- Coupling cap into IC1A.
- R6, 100 kΩ
- Biases IC1A’s plus input at 4.5 V.
- IC1A, JRC4558D
- Clipping stage, non-inverting, with diodes across its feedback.
- C5, 1 µF
- In series with R8, so the stage’s gain falls to 1 at DC and below about 34 Hz.
- R8, 4.7 kΩ
- The gain leg to the 4.5 V reference. Gain is 1 + (R7 + Overdrive) / 4.7 kΩ.
- R7, 10 kΩ
- Least feedback resistance, so the gain never drops below about 3.
- Overdrive, 1 MΩ pot, audio taper
- Overdrive, a 1 MΩ pot used as a variable resistor in the feedback. Turned up, the gain rises to about 220. Audio taper is assumed.
- D1, D2, D3, 2 × 1N914 / 1N4148 one way, 1N914 / 1N4148 the other way
- D2 and D3 in series one way, D1 the other, across the feedback. The redraw doesn’t name them, so 1N914s are assumed.
- R9, 10 kΩ
- Input resistor of the inverting stage.
- R10, 10 kΩ
- Biases U1B’s plus input at 4.5 V.
- U1B, JRC4558D
- Inverting stage, a gain of 1 with a treble cut.
- R11, 10 kΩ
- Feedback resistor. With R9 it sets the gain at 1.
- C6, 1 nF
- Across R11. The treble falls from about 16 kHz.
- C7, 1 µF
- Coupling cap to the tone network.
- R12, 4.7 kΩ
- Series resistor into the tone network.
- C8, 10 nF
- The treble path to Tone’s bright end.
- R13, 47 kΩ
- With C9, the darker path to Tone’s other end, a treble cut from about 720 Hz.
- C9, 4.7 nF
- To the 4.5 V reference, so it shunts treble at R13’s end.
- Tone, 100 kΩ pot, linear taper
- Tone, 100 kΩ. Its wiper fades from the darker path to the treble path. Linear is assumed.
- Level, 50 kΩ pot, audio taper
- Level, 50 kΩ, from the Tone wiper to the 4.5 V reference. Audio taper is assumed.
- C10, 47 nF
- Coupling cap into the output buffer.
- R15, 1 MΩ
- Biases Q2’s base at 4.5 V.
- Q2, 2SC1815
- Output buffer, an emitter follower.
- R16, 10 kΩ
- Q2’s emitter resistor.
- R17, 1 kΩ
- Output series resistor.
- C11, 1 µF
- Output coupling cap.
About this version
- A-3
- Values from a later redraw. The transistors and diodes aren’t named there, so the 2SC1815 and 1N914 models stand in.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.