Two-6AQ5 reverb and tremolo amp, mid 1960s style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Gibson GA-17RVT Scout.
Two 6EU7 stages with a bridged-T notch and the Volume pot between them, a cathodyne into two cathode-biased 6AQ5s with no feedback, a 12AX7 reverb and a phase-shift tremolo fed into the output tubesβ grid leaks.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar goes through 68 kΞ© straight to the first 6EU7 grid, with no coupling cap. After that stage a .001 Β΅F feeds a bridged-T: two 220 kΞ© with 500 pF across them and .003 Β΅F from their middle to ground. It makes a dip in the mids, near 600 Hz, and the .001 Β΅F ahead of it thins the bass. The Volume pot follows, then a second 6EU7 stage, and a .005 Β΅F into a 6EU7 cathodyne that drives two 6AQ5s on one 270 Ξ© cathode resistor with no feedback. The reverb is fed from the top of the Volume pot, so the Volume setting doesnβt change how hard the springs are driven, and it comes back through 1 MΞ© into the second stageβs grid. The tremoloβs oscillator swings the output tubesβ grids together through .047 Β΅F and 1 MΞ©, so their bias moves up and down. Thereβs no Depth control.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 68k, 68βkΞ©
- Input 1βs resistor, 68 kΞ© straight to the first grid. Thereβs no coupling cap at the input.
- 68k, 68βkΞ©
- From the first grid to input 2βs tip, 68 kΞ©.
- 1M, 1βMΞ©
- Input 2βs 1 MΞ© to ground. Itβs the first gridβs path to ground, through the 68 kΞ©.
- V2A, 6EU7
- One half of V2, a 6EU7, the first stage.
- 470k, 470βkΞ©
- Plate resistor for V2A, 470 kΞ©. The drawing reads +120 V on the plate.
- 4.7k, 4.7βkΞ©
- Cathode resistor for V2A, +1.2 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V2Aβs cathode resistor, so the stage has its full gain.
- .001Β΅, 1βnF
- Coupling cap into the bridged-T, only .001 Β΅F, so the bass is thinned before the Volume pot.
- 220k, 220βkΞ©
- First half of the bridged-T.
- 220k, 220βkΞ©
- Second half of the bridged-T, to the Volume potβs top.
- 500p, 500βpF
- Across both 220 kΞ©. It carries the treble past the bridged-T.
- .003Β΅, 3βnF
- From the middle of the two 220 kΞ© to ground. With the 500 pF it makes a dip in the mids, near 600 Hz.
- Volume, 500βkΞ© pot, audio taper
- Volume, 500 kΞ© audio. Its top also feeds the Reverb pot.
- 470k, 470βkΞ©
- From the Volume wiper to V2Bβs grid, 470 kΞ©. With the reverbβs 1 MΞ© it mixes the dry signal and the reverb at the grid.
- V2B, 6EU7
- The other half of V2, the second stage. The reverb comes in on its grid.
- 470k, 470βkΞ©
- Plate resistor for V2B, 470 kΞ©. The drawing reads +130 V on the plate.
- 4.7k, 4.7βkΞ©
- Cathode resistor for V2B, +1.2 V on the drawing.
- .1Β΅, 100βnF
- Only .1 Β΅F across V2Bβs 4.7 kΞ©, so the stage has its full gain only from a few hundred hertz up, and the bass is held down here.
- .005Β΅, 5βnF
- Coupling cap to the cathodyneβs grid.
- Reverb, 2βMΞ© pot, audio taper
- Reverb, 2 MΞ© audio, from the top of the Volume pot to ground. Its wiper is V1Aβs grid, so it sets how hard the springs are driven, whatever the Volume setting.
- V1A, 12AX7 / ECC83 / 7025
- One half of V1, a 12AX7 by the drawingβs tube chart, the reverb driver. Its plate goes straight into the reverb transformer.
- 1k, 1βkΞ©
- Cathode resistor for the reverb driver.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for the reverb driverβs cathode resistor.
- T3, 10βkΞ© to 8βΞ©, 10βH primary, 50βmH leakage
- The reverb transformer, from the driverβs plate to the spring unit. The drawing reads 2 V across its primary. Its figures, 10 kΞ© into 8 Ξ©, are typical for the job.
- Unit in R, 800βmΞ©
- Resistance of the reverb unitβs input coil. The current through it drives the springs, which play from a measured tankβs impulse response, a recording of how the real springs ring after a click.
- Unit in L, 1.1βmH
- Inductance of the reverb unitβs input coil, a measured long tankβs figure.
- Unit out L, 350βmH
- The reverb unitβs output coil, 0.35 H, from V1Bβs grid to ground. The springs come back in series with it.
- Unit out R, 181βΞ©
- Resistance of the unitβs output coil, 181 Ξ©, a measured long tankβs figure.
- 220k, 220βkΞ©
- Grid resistor for the reverb recovery stage.
- .001Β΅, 1βnF
- From the recovery grid to ground. It trims the springsβ highest treble.
- V1B, 12AX7 / ECC83 / 7025
- The other half of V1, the reverb recovery stage.
- 100k, 100βkΞ©
- Plate resistor for V1B, +190 V on the drawing.
- 2.2k, 2.2βkΞ©
- Cathode resistor for V1B.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V1Bβs cathode resistor.
- .005Β΅, 5βnF
- Coupling cap from the recovery stage.
- 1M, 1βMΞ©
- From the recovery stage into V2Bβs grid, where the reverb meets the dry signal.
- 150k, 150βkΞ©
- Plate resistor for the oscillator, from the +263 V node. The drawing reads +118 V on the plate.
- V3B, 6EU7
- The other half of V3 (V3A is the cathodyne in the power amp), the tremolo oscillator. Its cathode goes straight to ground.
- .022Β΅, 22βnF
- First cap of the oscillatorβs phase-shift ladder.
- 330k, 330βkΞ©
- The ladderβs first leg to ground.
- .022Β΅, 22βnF
- Second ladder cap.
- 150k, 150βkΞ©
- In series with the Frequency pot, the ladderβs second leg. It sets the top speed.
- Frequency, 1.5βMΞ© pot, reverse audio taper
- Frequency, 1.5 MΞ© reverse audio, as a variable resistor from the 150 kΞ© to the foot switch. Turned up, its resistance drops and the oscillator runs faster.
- .01Β΅, 10βnF
- Third ladder cap, into the grid. At one frequency the three caps and legs turn the plateβs swing upside down by the time it reaches the grid, so the stage oscillates at that frequency.
- 4.7M, 4.7βMΞ©
- Grid leak for the oscillator, and the ladderβs last leg. The drawing reads β0.6 V on the grid.
- .047Β΅, 47βnF
- Couples the oscillatorβs swing from its plate toward the output tubesβ grid leaks, and blocks the plateβs DC.
- 1M, 1βMΞ©
- From the .047 Β΅F to where the output tubesβ grid leaks meet. With the 330 kΞ© below it, it sets how much of the swing reaches both output grids, so it fixes the depth.
- 330k, 330βkΞ©
- From the grid leaksβ common node to ground. Itβs their DC return.
- V4, 6EU7
- 6EU7, a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 100k, 100βkΞ©
- The cathodyneβs plate resistor, the output to tube B.
- 2.7k, 2.7βkΞ©
- The cathodyneβs bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 100k, 100βkΞ©
- The cathodyneβs cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470βkΞ©
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathodeβs high DC voltage. Itβs the gridβs only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ξ©.
- .01Β΅, 10βnF
- Coupling cap to tube Aβs grid.
- .01Β΅, 10βnF
- Coupling cap to tube Bβs grid.
- V5, 6AQ5
- 6AQ5, tube A of the push-pull pair, its cathode on the shared cathode resistor, so it biases itself.
- V6, 6AQ5
- 6AQ5, tube B of the pair.
- 220k, 220βkΞ©
- Grid leak for tube A, returned with tube Bβs to the tremoloβs Depth pot, so the oscillator swings both grids together. The bias comes from the cathode resistor. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. Thatβs blocking distortion.
- 220k, 220βkΞ©
- Grid leak for tube B.
- 270, 270βΞ©
- The shared cathode resistor. Every output tubeβs current runs through it and lifts the cathodes above the grids, and thatβs the bias. Driven hard, the pair draws more current on average, so the cathodes climb and the tubes run colder, which softens the clipping.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signalβs frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 3.9k, 3.9βkΞ©
- Dropping resistor from B+ to the node for the reverb driver, as on the Gibson GA-17RVT Scout drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the reverb driver. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 4.7k, 4.7βkΞ©
- Dropping resistor from the node for the reverb driver to the node for the cathodyne, the reverb recovery and the tremolo, as on the Gibson GA-17RVT Scout drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the cathodyne, the reverb recovery and the tremolo. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 4.7k, 4.7βkΞ©
- Dropping resistor from the node for the cathodyne, the reverb recovery and the tremolo to the node for the preamp, as on the Gibson GA-17RVT Scout drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 8βkΞ© to 8βΞ©, 10βH primary, 10βmH leakage
- The output transformer, 8 kΞ© plate to plate into 8 Ξ©, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 262 V ac, 60 Hz
- One half of the power transformerβs high-voltage winding, 262 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 262 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 100βΞ©
- Resistance of one half of the winding, plus the primaryβs share. With the rectifierβs own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 100βΞ©
- Resistance of the other half. Typical of the part.
- V7, 6CA4
- One plate of the 6CA4 rectifier. It conducts near the peak of its half of the winding, and its own drop rises with the current, which adds to the sag.
- V7, 6CA4
- The rectifierβs other plate, on the other half cycle.
- 20Β΅, 20βΒ΅F electrolytic
- The reservoir cap. It feeds the output transformerβs center tap. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 8.69βΞ©
- Voice coil resistance, the floor of the speakerβs impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ξ© peak near 74 Hz on 8 Ξ©), scaled to the 8 Ξ© tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256βΒ΅H
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 464βΒ΅H
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3βΞ©
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13βmH
- A second step in the treble rise, with Loss R2 across it: a real voice coilβs losses keep climbing from a few hundred hertz.
- Loss R2, 2.19βΞ©
- Limits what Loss L2 adds.
- Tank R, 83.7βΞ©
- Height of the bass resonance, about 92 Ξ© in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 21.1βmH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220βΒ΅F
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The 6EU7 model is fitted to the Tung-Sol reissue plate chart. V1 is a 12AX7 by the drawingβs tube chart. The reverb transformer and unit are typical.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.