Six-stage JFET phaser on ±15 V, 1972 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Maestro PS-1 Phase Shifter.
An emitter follower feeds six op-amp phase stages, each turned by a JFET, and the sixth stage is mixed back with the dry signal through two 47 kΩ resistors. A triangle LFO with three speeds sweeps the six JFETs together.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Six stages make three notches, at the pitches where the wet signal has turned 180°, 540° and 900° against the dry one. The dry and wet signals meet through equal 47 kΩ resistors, so the notches are deep. There are no knobs. The two switches add 100 kΩ or 47 kΩ from +15 V to the speed node, which raises the voltage that sets the triangle’s speed. Medium alone sweeps about 0.9 times a second, Fast alone about 1.7, and both together about 2.3. With both off the sweep takes many seconds. The 220 µF there makes the speed change glide over about two seconds. Inside, Osc. Ampl. sets how far the triangle swings the JFET gates, and FET Bias sets where they sit. The model runs on a steady ±15 V in place of the mains supply.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- −15 V, -15 V
- The −15 V rail, made from the mains in the unit, a steady source here.
- C1, 330 nF
- Input coupling cap.
- R1, 33 kΩ
- From the input to ground. It sets the input impedance near 33 kΩ.
- R2, 10 kΩ
- Series resistor into Q1’s base.
- Q1, 2N3906
- The input buffer, a PNP emitter follower (2N3638A on the drawing). Its emitter drives the six stages and the dry side of the mix.
- R3, 10 kΩ
- Q1’s emitter load, from +15 V.
- R40, 100 kΩ
- Into the minus input. With the feedback resistor it makes the inverting half of the stage.
- R41, 100 kΩ
- Feedback, equal to the input resistor, so every frequency comes out at the same level and only the phase moves.
- C2, 10 nF
- Feeds the plus input. Against the JFET and the 100 kΩ beside it, it sets where this stage turns the phase 90°, about 160 Hz with the JFET pinched off.
- R42, 100 kΩ
- From the plus input to ground, beside the JFET.
- Q3, 2N5952
- A 2N5952 JFET used as a resistor that the LFO varies. The drawing marks these “selected”. The closer the gate comes to 0 V, the lower its resistance and the higher this stage’s 90° point.
- IC1A, MC1458
- Half a 1458, the first of six phase-shift stages.
- R43, 100 kΩ
- Into the minus input, as in the first stage.
- R44, 100 kΩ
- Feedback, equal to the input resistor.
- C3, 10 nF
- Feeds the plus input, as in the first stage.
- R45, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q4, 2N5952
- This stage’s JFET, on the same gate line as the others.
- IC1B, MC1458
- Half a 1458, phase-shift stage 2.
- R46, 100 kΩ
- Into the minus input, as in the first stage.
- R47, 100 kΩ
- Feedback, equal to the input resistor.
- C4, 10 nF
- Feeds the plus input, as in the first stage.
- R48, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q5, 2N5952
- This stage’s JFET, on the same gate line as the others.
- IC2A, MC1458
- Half a 1458, phase-shift stage 3.
- R49, 100 kΩ
- Into the minus input, as in the first stage.
- R50, 100 kΩ
- Feedback, equal to the input resistor.
- C5, 10 nF
- Feeds the plus input, as in the first stage.
- R51, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q6, 2N5952
- This stage’s JFET, on the same gate line as the others.
- IC2B, MC1458
- Half a 1458, phase-shift stage 4.
- R52, 100 kΩ
- Into the minus input, as in the first stage.
- R53, 100 kΩ
- Feedback, equal to the input resistor.
- C6, 10 nF
- Feeds the plus input, as in the first stage.
- R54, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q7, 2N5952
- This stage’s JFET, on the same gate line as the others.
- IC3A, MC1458
- Half a 1458, phase-shift stage 5.
- R55, 100 kΩ
- Into the minus input, as in the first stage.
- R56, 100 kΩ
- Feedback, equal to the input resistor.
- C7, 10 nF
- Feeds the plus input, as in the first stage.
- R57, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q8, 2N5952
- This stage’s JFET, on the same gate line as the others.
- IC3B, MC1458
- Half a 1458, the sixth phase-shift stage. Its output is the wet signal.
- R28, 1 MΩ
- From the output offset trimmer into the sixth stage. It trims the DC at the output so the bypass switch doesn’t click.
- Offset, 10 kΩ pot, linear taper
- The output offset trimmer, 10 kΩ from −15 V to +15 V, set at its center.
- R4, 47 kΩ
- The dry signal into the mix.
- R5, 47 kΩ
- The wet signal into the mix, equal to the dry. Where the six stages have turned it 180°, 540° or 900°, the two cancel.
- R6, 10 kΩ
- Divides the mix down, after the effect switch (drawn as a wire).
- R7, 47 kΩ
- In series with the output jack.
- R20, 100 kΩ
- Medium Phase’s resistor from +15 V.
- R21, 47 kΩ
- Fast Phase’s resistor from +15 V.
- R22, 1 MΩ
- From +15 V to the speed node. With the switches off it sets the slow speed.
- R23, 220 kΩ
- From the speed node to −15 V.
- R24, 10 kΩ
- From the speed node to ground. With the switches off the node sits about 0.5 V under 0 V.
- C8, 220 µF electrolytic
- 220 µF. Against about 10 kΩ it takes a couple of seconds for the speed to change after a switch.
- Q2, 2N3906
- An emitter follower (2N3638A on the drawing). Its emitter is the speed voltage, about 0.6 V over the speed node.
- R25, 47 kΩ
- Q2’s emitter load, from +15 V.
- R26, 10 kΩ
- With R27, holds the integrator’s plus input at half the speed voltage.
- R27, 10 kΩ
- The lower half of that divider.
- Q9, 2N4303
- A 2N4302 (2N4303 figures) used as a switch. With the square high it is on, and the speed voltage feeds the integrator through R29, so the triangle ramps down.
- R29, 150 kΩ
- The ramp-down current’s resistor.
- R30, 150 kΩ
- The ramp-up current’s resistor.
- Q10, 2N4360
- A P1069C, a P-channel JFET (2N4360 figures) used as a switch. With the square low it is on and grounds R30, so the triangle ramps up.
- R31, 1 MΩ
- Drives the 2N4302’s gate from the square.
- R32, 1 MΩ
- Drives the P1069C’s gate from the square.
- C9, 330 nF
- The integrator’s cap. The current into it sets how fast the triangle ramps.
- IC4a, MC1458
- Half a 1458, the integrator. Its output is the triangle.
- R33, 10 kΩ
- The triangle into the comparator’s plus input.
- R34, 33 kΩ
- Positive feedback from the comparator’s output. With R33 it sets the triangle’s peaks at about ±4 V.
- IC4b, MC1458
- Half a 1458, the comparator. Its output flips each time the triangle reaches a peak.
- Osc. Ampl., 10 kΩ pot, linear taper
- The Osc. Ampl. trimmer, 10 kΩ: how much of the triangle reaches the gates, so how far the notches sweep. Set at 0.3, assumed.
- R35, 33 kΩ
- The triangle into the gate drive node.
- R36, 10 kΩ
- From −15 V to the top of FET Bias.
- FET Bias, 10 kΩ pot, linear taper
- The FET Bias trimmer, 10 kΩ, from about −7.5 V to ground. It sets where the gates sit, so where the sweep is centered. Set for this file’s JFET.
- R37, 33 kΩ
- The bias into the gate drive node.
- C10, 4.7 µF electrolytic
- Smooths the gate drive. It rounds the triangle’s corners into a curve.
- R38, 10 kΩ
- To the gate line.
About this version
- As drawn
- Steady ±15 V. 2N3906 for the 2N3638A, 2N5952 stage JFETs, MC1458 op-amps. The trimmers are set as the adjustment procedure says, for this file’s JFET.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.