Diode bridge and transformer octave with a twin-T filter, 1972 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Maestro BB-1 Bass Brass.
A diode bridge into a center-tapped transformer turns the note into its octave up. A twin-T filter then lifts one band of it, and Bass and Brass volumes mix the dry note and the filtered octave.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q5 splits the note into two opposite copies. The diode bridge passes each half of the wave through one half of T1’s primary, both in the same direction, so the secondary carries the wave folded up, an octave above the note. Q7 drives the twin-T’s middle legs, and the twin-T sits in Q6’s feedback. At the twin-T’s notch Q6’s feedback falls away, so its gain peaks there: near 680 Hz on Brass 1 and near 5 kHz on Brass 2. Harmonics adds the unfiltered octave to the Brass mix. Bass sets the dry note from Q1. The model leaves out the footswitch.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R30, 820 Ω
- Feeds the output stages’ 8 V supply.
- C17, 10 µF electrolytic
- Filters the 8 V supply.
- C1, 100 nF
- Input coupling cap.
- R1, 150 kΩ
- From Q1’s base to ground.
- R2, 150 kΩ
- Collector to base. With R1 it biases Q1.
- R3, 12 kΩ
- Q1’s collector load.
- Q1, 2N3392
- Input stage. Its collector feeds the octave side and its emitter the dry Bass side.
- R4, 390 Ω
- Q1’s emitter resistor, unbypassed.
- C8, 1 µF electrolytic
- Couples Q1’s emitter to the Bass volume.
- Bass, 10 kΩ pot, audio taper
- Bass Volume, 10 kΩ, the dry note’s level in the mix. Audio taper is assumed.
- R15, 10 kΩ
- Mixing resistor from the Bass volume.
- C2, 100 nF
- Couples Q1’s collector to Sensitivity.
- Sensitivity, 50 kΩ pot, audio taper
- Sensitivity, the level into the octave side. The drawing shows no value: 50 kΩ audio is assumed.
- C3, 100 nF
- Couples Sensitivity to Q4.
- R5, 1.5 MΩ
- Collector to base. It biases Q4 and sets Q5’s base voltage with it.
- R6, 12 kΩ
- Q4’s collector load.
- Q4, 2N3392
- Gain stage ahead of the modulator driver.
- R7, 150 Ω
- Q4’s emitter resistor.
- C15, 50 nF
- Trims Q4’s treble before the bridge, from about 270 Hz against R6.
- R8, 2.2 kΩ
- Q5’s collector load.
- Q5, 2N3392
- Modulator driver, a phase splitter. Its collector and emitter carry equal and opposite copies of the note.
- R9, 2.2 kΩ
- Q5’s emitter load, equal to R8.
- C4, 1 µF electrolytic
- Couples Q5’s collector to one corner of the bridge.
- C5, 1 µF electrolytic
- Couples Q5’s emitter to the opposite corner, which also goes to the primary’s center tap.
- D1, 1N914 / 1N4148
- One of the bridge’s four diodes. The drawing names no type, so 1N914s are assumed.
- D1, 1N914 / 1N4148
- One of the bridge’s four diodes.
- D1, 1N914 / 1N4148
- One of the bridge’s four diodes.
- D1, 1N914 / 1N4148
- One of the bridge’s four diodes.
- Primary, top half, 1.26 H
- Top half of T1’s primary. It carries the current while C5’s side of the wave is higher. The transformer figures are typical for the size.
- Primary, bottom half, 1.26 H
- Bottom half of the primary, wound the same way. It carries the current while C4’s side is higher, in the same direction, so the flux always goes one way.
- Rp, 250 Ω
- Resistance of one primary half, in the center-tap lead that both halves’ currents return through. A typical value.
- Secondary, 5 H
- T1’s secondary. It passes the folded wave’s swing, the octave, and none of its DC.
- A–B, coupling factor 0.990
- Coupling between the two primary halves.
- A–S, coupling factor 0.990
- Coupling between the top half and the secondary.
- B–S, coupling factor 0.990
- Coupling between the bottom half and the secondary.
- C14, 10 nF
- Across the secondary. It trims the octave’s top end.
- C13, 100 nF
- Couples the octave to the filter drive.
- R17, 220 kΩ
- Top of Q7’s base bias divider.
- R16, 220 kΩ
- Bottom of Q7’s base bias divider.
- Q7, 2N3392
- Filter drive, an emitter follower. It drives the twin-T’s two middle legs.
- R18, 2.2 kΩ
- Q7’s emitter resistor.
- R29, 82 kΩ
- Through SW2 at Hi, it adds the unfiltered octave to the Brass volume.
- R25, 47 kΩ
- Twin-T, top arm, from Q6’s collector.
- R23, 47 kΩ
- Twin-T, top arm, to Q6’s base. With 0.005 µF the notch sits near 680 Hz.
- R24, 6.8 kΩ
- Across R25 in Brass 2. Unnumbered on the drawing.
- R27, 6.8 kΩ
- Across R23 in Brass 2. Unnumbered on the drawing.
- C11, 10 nF
- Twin-T, the top arm’s middle leg, driven from Q7. Unnumbered on the drawing.
- C10, 5 nF
- Twin-T, bottom arm, from Q6’s collector.
- C9, 5 nF
- Twin-T, bottom arm, to Q6’s base.
- R22, 22 kΩ
- Twin-T, the bottom arm’s middle leg, driven from Q7.
- R26, 3.3 kΩ
- Across R22 in Brass 2.
- R20, 47 kΩ
- Q6’s collector load.
- R21, 1.5 MΩ
- Collector to base. It biases Q6.
- Q6a, 2N5306 (half)
- First half of the Q6 Darlington, the filter amp.
- Q6b, 2N5306 (half)
- Second half of the Q6 Darlington. The pair’s gain is the two gains multiplied, so the feedback sets the response.
- R19, 1 kΩ
- Q6’s emitter resistor.
- C12, 50 nF
- Couples the filter amp’s output toward the Brass volume.
- R28, 150 kΩ
- Series resistor to the Brass volume.
- Brass, 10 kΩ pot, audio taper
- Brass Volume, 10 kΩ, the filtered octave’s level in the mix. Audio taper is assumed.
- R12, 10 kΩ
- Mixing resistor from the Brass volume.
- C6, 1 µF electrolytic
- Couples the mix into Q2.
- R11, 470 kΩ
- Collector to base. It biases Q2. The drawing marks it with an asterisk, likely a value set at the factory.
- R10, 10 kΩ
- Q2’s collector load.
- Q2, 2N3392
- Output preamp, a gain stage.
- R14, 470 Ω
- Q2’s emitter resistor. With R10 it sets the gain near 20.
- Q3, 2N3392
- Output emitter follower.
- R13, 4.7 kΩ
- Q3’s emitter resistor.
- C7, 1 µF electrolytic
- Output coupling cap.
About this version
- BB-1
- Values from the original schematic. The 2N5308 Darlington uses the 2N5306 model. T1 is a 10 kΩ : 10 kΩ center-tapped part with typical figures.
Sources
- R.G. Keen, GEO, the original schematic annotated, with the twin-T filter redrawn
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.