Band-pass envelope filter with a transistor tuning it, 1981 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Vox 1904 Wah.
An auto-wah on one dual op-amp. A band-pass filter’s peak is set by a transistor working as a resistor, and the guitar’s level, rectified, sets the transistor’s base current. Sensitivity sets how much of the guitar reaches the envelope.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC1A is a band-pass filter. With Q1 off its peak sits near 200 Hz, about 13 dB over the input. Q1 connects node X to ground with no DC across it, so it works as a resistor set by its base current. As that resistance falls the peak moves up, to about 570 Hz with 0.5 V on the base, 1.4 kHz at 0.55 V and 3 kHz at 0.6 V. IC1B amplifies the guitar about 70 times. C6 and R7 cut below about 1.7 kHz, so the envelope follows the pick’s attack more than the note’s body. Its plus input is on ground, so only negative swings raise its output. D2 charges C7, and R10 and R11 divide C7’s voltage down to Q1’s base. C7 drains through them and through R12 and R13, so the peak falls back as the note dies. The envelope needs a hard pick. A 200 mV pick at full Sensitivity barely moves the peak, and a 500 mV pick moves it to about 2 kHz. The bench’s MC1458 model rests 1.8 V over ground on a 9 V supply, and the guitar never swings it out of that, so an LM358 model stands in for the envelope half. The footswitch, the LED and the battery’s series diode are left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R3, 470 kΩ
- Top of the Vbias divider.
- R2, 470 kΩ
- Bottom of the Vbias divider. With R3 it sets Vbias at 4.5 V.
- C3, 10 µF electrolytic
- Filters Vbias.
- R1, 47 kΩ
- The filter’s input resistor, into node X.
- C2, 5 nF
- One of the filter’s two tuning caps, from X to the minus input.
- C1, 5 nF
- The other tuning cap, from X to the output.
- R4, 470 kΩ
- The filter’s feedback resistor.
- C4, 1 nF
- From the minus input to ground.
- IC1A, MC1458
- Half of the LM1458N, the filter.
- Q1, 2SC828
- 2SC693F. Its collector sits at 0 V, so it works as a resistor from X to ground, lower with more base current. Lower resistance moves the peak up. With Q1 off the peak rests near 210 Hz.
- C5, 56 nF
- Output coupling cap.
- R5, 150 kΩ
- Holds the output at 0 V DC.
- Sensitivity, 500 kΩ pot, reverse audio taper
- R6, 500 kΩ reverse audio (marked C), across the input. It sets how much of the guitar reaches the envelope amp. Its name on the panel is not on the drawing.
- C6, 2 nF
- Coupling cap into the envelope amp. With R7 it cuts below about 1.7 kHz, so the envelope follows the pick’s bright attack more than the note’s body.
- R7, 47 kΩ
- The envelope amp’s input resistor. With R8 it sets the gain at about 70.
- IC1B, LM358
- The other half, the envelope amp. Its plus input is on ground, so it rests at its low limit and only the guitar’s negative halves swing it up. An LM358 model stands in here, since the bench’s MC1458 model rests too far over ground for the guitar to move it.
- R8, 3.3 MΩ
- The envelope amp’s feedback resistor.
- D2, 1N914 / 1N4148
- 1S953, charges C7 on the envelope amp’s peaks.
- R9, 100 Ω
- Limits the charging current into C7.
- C7, 10 µF
- The envelope cap, 10 µF bipolar. It charges on each pick and drains through R10, R11, R12 and R13.
- R12, 12 kΩ
- In series with R13, a drain for C7.
- R13, 2 MΩ pot, linear taper
- R13, a 2 MΩ variable resistor. With R12 it sets how fast C7 drains, so how fast the peak falls back. Set at the middle (assumed).
- R10, 33 kΩ
- From the envelope cap to Q1’s base.
- R11, 10 kΩ
- From Q1’s base to ground. With R10 it divides the envelope down, so C7 must charge over about 2.5 V before Q1 conducts.
About this version
- Stock
- Negative ground, 9 V. LM1458N dual op-amp, 2SC693F tuning transistor (a 2SC828 model stands in).
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.