Single-ended 6AQ5 amp with cathode tremolo, late 1960s style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Univox U-45.
A 12AX7 stage, a treble-cut Tone and a Volume into a 6AV6 driver and one 6AQ5, single-ended, off a 6X4. The other 12AX7 half is a tremolo oscillator that works through the first stage’s cathode.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar comes in through 220 kΩ, and the two empty jacks ground their own 220 kΩ, so the first stage sees a third of the signal. The first stage is half a 12AX7 with a 470 kΩ plate resistor and a 1.5 MΩ from its plate to ground. Two .01 µF coupling caps with 470 kΩ between them pass little under about 60 Hz. The Tone control is a .005 µF cap to ground through a variable resistor, so turned down it cuts the treble. The tremolo oscillator’s cathode current runs through the first stage’s 4.7 kΩ cathode resistor. As that current swings, it moves the first stage’s bias and its gain. The 6AQ5 runs single-ended in class A on about 250 V.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 220k, 220 kΩ
- Input resistor from the Guitar jack.
- 220k, 220 kΩ
- Input resistor from the Acc jack. With no plug in, the jack grounds its end, so it loads the grid.
- 220k, 220 kΩ
- Input resistor from the Aux jack, the same.
- V1a, 12AX7 / ECC83 / 7025
- Half of V1, a 12AX7, the only preamp stage. Its grid’s path to ground is the empty jacks’ 220 kΩ resistors.
- 470k, 470 kΩ
- Plate resistor, from the 220 V node (+90 V on the drawing).
- 1.5M, 1.5 MΩ
- From the plate to ground, 1.5 MΩ, as drawn. With the 470 kΩ it lowers the plate’s voltage and the stage’s gain slightly.
- 4.7k, 4.7 kΩ
- Cathode resistor (+1.1 V on the drawing). The tremolo oscillator’s current runs through it too.
- 10µ, 10 µF electrolytic
- Bypass across the cathode resistor. It holds the cathode still for the guitar above about 3 Hz, so the tremolo’s swing, a few hertz, still moves it.
- .01µ, 10 nF
- First coupling cap from the plate.
- 470k, 470 kΩ
- To ground between the two coupling caps.
- .01µ, 10 nF
- Second coupling cap, to the Tone and Volume. With the first and the 470 kΩ it passes little under about 60 Hz.
- .005µ, 5 nF
- The Tone control’s cap, to the Tone pot.
- Tone 500k, 500 kΩ pot, audio taper
- Tone, 500 kΩ audio, wired as a variable resistor from the cap to ground. Turned up, it puts more resistance in series with the cap, so less treble is bled away. Up is assumed to be brighter.
- Vol 500k, 500 kΩ pot, audio taper
- Volume, 500 kΩ audio. Its wiper is the 6AV6’s grid, and the pot is that grid’s path to ground.
- V1b, 12AX7 / ECC83 / 7025
- The other half of V1, the tremolo’s oscillator. A ladder of three caps from its plate back to its grid turns the plate’s swing round by half a cycle at a few hertz, so the stage oscillates there.
- 220k, 220 kΩ
- The oscillator’s plate resistor, from the 220 V node (+150 V on the drawing).
- .02µ, 20 nF
- First cap of the ladder, from the oscillator’s plate.
- 390k, 390 kΩ
- The ladder’s first leg, 390 kΩ, with the Speed pot under it.
- Speed 1M, 1 MΩ pot, reverse audio taper
- Speed, 1 MΩ, a variable resistor under the 390 kΩ. Turned up, there’s less track in the circuit and the oscillator runs faster. The drawing marks its taper C, read here as reverse audio. Faster clockwise is assumed.
- .02µ, 20 nF
- Second cap of the ladder.
- 390k, 390 kΩ
- The ladder’s second leg, to ground.
- .02µ, 20 nF
- Last cap of the ladder, into the oscillator’s grid.
- 390k, 390 kΩ
- The oscillator’s grid leak, 390 kΩ to ground.
- 10k, 10 kΩ
- From the oscillator’s cathode to the first stage’s cathode. With the switch open it cuts the oscillator’s gain enough to stop it.
- V2, 6AV6
- 6AV6, the driver. With one output tube there’s no phase inverter, only a gain stage to raise the preamp’s signal enough to drive the output grid. The feedback from the speaker goes to its cathode. Its grid connects straight to the preamp’s output with no coupling cap, so its path to ground is through the preamp’s volume and tone network.
- 100k, 100 kΩ
- Plate resistor for the driver. Its plate drives the output tube’s grid through the coupling cap.
- 3.3k, 3.3 kΩ
- Cathode resistor for the driver. It sets the driver’s bias, a volt or two. It sits on the feedback leg, so the fed-back signal moves the cathode.
- 10µ, 10 µF electrolytic
- Bypass cap across the driver’s cathode resistor, for full gain above a few hertz. It goes to the top of the feedback leg, not to ground, so the feedback still reaches the cathode.
- 2.2k, 2.2 kΩ
- The feedback resistor from the speaker. With the 100 Ω below it, it sends about 4 % of the speaker voltage back to the driver’s cathode, which lowers the gain, flattens the response and tightens the bass. Its value isn’t marked on the drawing, so 2.2 kΩ, a typical value, is assumed.
- 100, 100 Ω
- The bottom of the feedback loop, 100 Ω to ground under the driver’s cathode resistor and its bypass cap. The bypass sits across the cathode resistor only, so the fed-back speaker voltage still moves the cathode. The driver’s current runs through it too, so it’s kept small.
- .005µ, 5 nF
- Coupling cap to tube A’s grid.
- V3, 6AQ5
- 6AQ5, the output tube, single-ended: it carries the whole signal, and its idle current runs through the transformer all the time. Its cathode resistor biases it.
- 470k, 470 kΩ
- Grid leak for tube A, to ground. The bias comes from the cathode resistor. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 250, 250 Ω
- The cathode resistor. The tube’s current runs through it and lifts the cathode above the grid, and that’s the bias. Driven hard, the tube draws more current on average, so the cathode climbs and the bias goes colder.
- 10µ, 10 µF electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 4.7k, 4.7 kΩ
- Dropping resistor from B+ to the screens. It’s large, so the screens sit about 30 V below the plates and drop further when they draw more current on a hard note.
- 10µ, 10 µF electrolytic
- Filter cap on the screen supply.
- 22k, 22 kΩ
- Dropping resistor from the screen supply node to the node for the driver and the preamp, as on the Univox U-45 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 3µ, 3 µF electrolytic
- Filter cap at the node for the driver and the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 5 kΩ to 8 Ω, 14 H primary, 30 mH leakage
- The output transformer, 5 kΩ from the plate to B+ into 8 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 236 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 236 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 236 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 150 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 150 Ω
- Resistance of the other half. Typical of the part.
- V4, 6X4
- One plate of the 6X4 rectifier. It conducts near the peak of its half of the winding, and its own drop rises with the current, which adds to the sag.
- V4, 6X4
- The rectifier’s other plate, on the other half cycle.
- 10µ, 10 µF electrolytic
- The reservoir cap. It feeds the output transformer’s B+ end. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 8.69 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 8 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256 µH
- Voice coil inductance. It makes the impedance rise through the treble. The feedback holds the output steadier against that than it would be without feedback.
- Loss L, 464 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 2.19 Ω
- Limits what Loss L2 adds.
- Tank R, 83.7 Ω
- Height of the bass resonance, about 92 Ω in all at its peak. The feedback holds the output steadier against that than it would be without feedback.
- Tank L, 21.1 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- Values from the factory drawing.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.