Three op-amp clipping stages with Attack, Punch and Edge, 1983 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Ibanez SM-9 Super Metal.
A JFET buffer and an op-amp stage with an Attack control between its inputs, then two inverting op-amp stages with an LED and a silicon diode across each feedback, and red LEDs to ground. An active bass control (Punch) and an Edge control that boosts or cuts two tuned bands near 1.2 kHz and 2.3 kHz follow.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 buffers the guitar. C2 into R5 and the Attack network cut the bass before any gain, about 10 dB at 100 Hz against 3 kHz. IC1Aβs treble gain is set by Attack. With the wiper toward the minus input, C4 and R7 raise it to about 5.5. IC1B and IC2A are inverting stages that share the Drive pot. Turning Drive up moves track into IC1Bβs feedback and out of IC2Aβs input, so both stages gain together. Each stage has a red LED one way and a silicon diode the other across its feedback, so each clips unevenly. The red LEDs to ground after R12 would clip at about 1.7 V, more than IC2A puts out, so they barely conduct. Punch is an active bass control, flat at noon. Edge moves two simulated inductors between IC3Aβs two inputs. Toward the minus input they boost their bands, toward the plus input they cut. R18 and R19 halve the signal into IC3A, and R27 with the 10 kΞ© Level halves it again, so the pedal is quiet. The model leaves out the electronic bypass and the supply filters.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R31, 10βkΞ©
- Top of the 4.5 V reference divider.
- R32, 10βkΞ©
- Bottom of the reference divider.
- C25, 47βΒ΅F electrolytic
- Filters the 4.5 V reference.
- R1, 10βkΞ©
- Input series resistor.
- C1, 47βnF
- Input coupling cap.
- R2, 1βMΞ©
- Biases Q1βs gate at 4.5 V and sets the input impedance near 1 MΞ©.
- Q1, 2N5457
- Input buffer, a 2N5457 source follower.
- R3, 10βkΞ©
- Q1βs source resistor.
- C2, 100βnF
- Coupling cap into IC1A.
- R4, 1βkΞ©
- Series resistor into IC1A.
- R5, 10βkΞ©
- Biases IC1Aβs plus input at 4.5 V.
- Attack, 20βkΞ© pot, s curve taper
- Attack, 20 kΞ© with an S-curve taper, between IC1Aβs two inputs. Its wiper goes to ground through C4 and R7. Turned up, toward the minus input, the treble gain rises. Turned down, the treble at the plus input is cut.
- C4, 220βnF
- With R7, from the Attack wiper to ground.
- R7, 220βΞ©
- With C4, sets IC1Aβs treble gain near 5.5 with Attack at full.
- IC1A, JRC4558D
- First stage, non-inverting, with the Attack network between its inputs.
- R6, 1βkΞ©
- IC1Aβs feedback resistor.
- C3, 33βnF
- Across R6. It rolls off IC1Aβs gain above about 4.8 kHz.
- C5, 220βnF
- Coupling cap into IC1B.
- R8, 4.7βkΞ©
- IC1Bβs input resistor.
- IC1B, JRC4558D
- Second stage, inverting, with an LED and a diode across its feedback.
- R9, 4.7βkΞ©
- With the Drive potβs first part, IC1Bβs feedback.
- Drive, 100βkΞ© pot, linear taper
- Drive, 100 kΞ© linear. Its wiper is IC1Bβs output. The part toward R9 is IC1Bβs feedback, the part toward R10 is in IC2Aβs input, so turning it up raises both stagesβ gain.
- C6, 100βpF
- Across IC1Bβs feedback. It rolls off the top of the clipped signal.
- D2, D3, 1N914 / 1N4148 one way, Red LED the other way
- D3, a red LED, one way and D2, a silicon diode, the other way across IC1Bβs feedback, so it swings about 1.4 V one way and 0.5 V the other.
- R10, 4.7βkΞ©
- With the Drive potβs other part, IC2Aβs input resistance.
- C7, 220βnF
- Coupling cap into IC2A.
- IC2A, JRC4558D
- Third stage, inverting, with an LED and a diode across its feedback.
- R11, 220βkΞ©
- IC2Aβs feedback resistor.
- C8, 100βpF
- Across IC2Aβs feedback. It rolls off the top of the clipped signal.
- D4, D5, 1N914 / 1N4148 one way, Red LED the other way
- D5, a red LED, one way and D4, a silicon diode, the other way across IC2Aβs feedback.
- C9, 1βΒ΅F
- Coupling cap toward the LEDs.
- R12, 10βkΞ©
- Feeds the LEDs and limits their current.
- D10, D11, Red LED, one each way
- D10 and D11, red LEDs back to back to ground. They would hold the signal to about 1.7 V either way, more than IC2A puts out, so they barely conduct.
- C10, 1βnF
- Across the LEDs. With R12 it trims the treble above about 16 kHz.
- C11, 1βΒ΅F
- Coupling cap into the bass stage.
- R13, 100βkΞ©
- Holds the bass stageβs input at 4.5 V.
- R14, 10βkΞ©
- Input resistor of the bass stage.
- Punch, 100βkΞ© pot, linear taper
- Punch, 100 kΞ© linear. Its wiper feeds IC2Bβs minus input. Turned up, toward R14, the bass is boosted. Turned down, itβs cut. Flat at noon.
- C12, 10βnF
- Across the Punch potβs input half. It lets the treble past the pot, so Punch works on the bass.
- C13, 10βnF
- Across the Punch potβs output half.
- R15, 10βkΞ©
- Feedback resistor of the bass stage.
- R16, 15βkΞ©
- From the Punch wiper to IC2Bβs minus input.
- R17, 10βkΞ©
- Biases IC2Bβs plus input at 4.5 V.
- C14, 30βpF
- Across IC2Bβs feedback. It rolls off the top end.
- IC2B, JRC4558D
- Bass stage, inverting.
- C15, 1βΒ΅F
- Coupling cap into the Edge stage.
- R18, 4.7βkΞ©
- Into IC3Aβs plus input. The branches on the plus side cut against it.
- R19, 4.7βkΞ©
- From IC3Aβs plus input to 4.5 V. With R18 it halves the signal.
- Edge, 20βkΞ© pot, s curve taper
- Edge, 20 kΞ© with an S-curve taper, one half of a dual pot between IC3Aβs two inputs. Its wiper feeds the 1.2 kHz branch. Turned up, toward the minus input, the band is boosted. Turned down, itβs cut.
- Edge (2.3 kHz), 20βkΞ© pot, s curve taper
- The other half of the dual Edge pot. Its wiper feeds the 2.3 kHz branch.
- IC3A, JRC4558D
- Edge stage. A tuned branch on its minus input boosts its band, one on its plus input cuts it.
- R20, 4.7βkΞ©
- IC3Aβs feedback resistor.
- C16, 5.6βnF
- Across R20. It rolls off above about 6 kHz.
- R21, 220βΞ©
- Sets how far the 1.2 kHz band can be boosted or cut.
- C17, 56βnF
- Tunes the 1.2 kHz branch with the simulated inductor.
- R22, 1.5βkΞ©
- Sets the 1.2 kHz branchβs width.
- C18, 2.2βnF
- With R22 and R23, it makes IC4A act as a 0.33 H inductor.
- R23, 100βkΞ©
- Biases IC4A at 4.5 V.
- IC4A, JRC4558D
- Follower of the 1.2 kHz branchβs simulated inductor (a gyrator).
- R24, 220βΞ©
- Sets how far the 2.3 kHz band can be boosted or cut.
- C19, 47βnF
- Tunes the 2.3 kHz branch with the simulated inductor.
- R26, 820βΞ©
- Sets the 2.3 kHz branchβs width.
- C20, 1.2βnF
- With R26 and R25, it makes IC4B act as a 0.1 H inductor.
- R25, 100βkΞ©
- Biases IC4B at 4.5 V.
- IC4B, JRC4558D
- Follower of the 2.3 kHz branchβs simulated inductor (a gyrator).
- C21, 1βΒ΅F
- Coupling cap out of the Edge stage.
- R27, 10βkΞ©
- In series ahead of Level. With the 10 kΞ© Level it halves the most output.
- Level, 10βkΞ© pot, audio taper
- Level, 10 kΞ© audio, to ground.
- C22, 100βnF
- Coupling cap into the output buffer.
- R28, 510βkΞ©
- Biases IC3B at 4.5 V.
- IC3B, JRC4558D
- Output buffer, a follower.
- R29, 470βΞ©
- In series at the output.
- C24, 10βΒ΅F electrolytic
- Output coupling cap.
About this version
- Stock values
- From a later redraw, at the stock values: R19 4.7 kΞ©, R27 10 kΞ©, and one dual-gang Edge pot. JRC4558D op-amps, a 2N5457 JFET, 1N914 diodes and red LEDs.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.