Tube oil can rotating sound with reverb, 1966 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Tel-Ray Deluxe Organ Tone.
A rotating speaker sound from a tube oil can, after the Tel-Ray Deluxe Organ Tone. The guitar goes onto a disc turning in oil at one writing brush and comes off at a reading brush 3 ms later. The disc’s speed swings once a turn, so the pitch wavers, and mixed with the dry guitar it swirls. A second writing brush records what was read again, for repeats.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The first triode amplifies the guitar. After it, the Response switch either leaves a .002 µF cap in series or shorts it, and Direct Sig. carries the dry guitar from there to A. A filter of 150 k, .015 µF and 120 k, with .0068 µF across it, feeds the second triode. That triode’s plate drives the top writing brush through a 2 M preset. A cathode follower reads the disc 3 ms later. Its output goes through 6.8 k and .022 µF, which cut above about 1 kHz. From there it goes to Organ-Tone Level and A, and to Reverb Sustain. Reverb Sustain feeds the fourth triode, which writes it onto the disc again at the bottom brush through Reverb Sig., so it comes round about 144 ms later. The Bypass Pedal shorts the read signal to ground.
Download.
Parts and what they do
Stock values for the 2 M preset version. Tap a part on the schematic to change it.
- Hi Level Control, 500 kΩ pot, audio taper
- Hi Level Control, 500 k, for the Hi Level Input. That jack drives its wiper. With nothing plugged in there, the pot and its 100 k are a 600 k load on the input node. Audio taper and its setting assumed.
- 100k, 100 kΩ
- From Hi Level Control’s top to the input node, 100 k.
- 100k, 100 kΩ
- The Instrument Input’s resistor, 100 k.
- .015µ, 15 nF
- Coupling cap into the first triode, .015 µF.
- 4.6M, 4.6 MΩ
- The first triode’s grid resistor, 4.6 M as drawn.
- V1a, 12AX7 / ECC83 / 7025
- The first triode, the input amp. The drawing names no tube, so a 12AX7 is assumed.
- 470k, 470 kΩ
- The first triode’s plate resistor, 470 k.
- 6.8k, 6.8 kΩ
- The first triode’s cathode resistor, 6.8 k.
- 50µ, 50 µF electrolytic
- The first triode’s cathode bypass, 50 µF.
- .068µ, 68 nF
- Coupling cap out of the first triode, .068 µF.
- 1M, 1 MΩ
- From the .068 µF to ground, 1 M.
- .002µ, 2 nF
- In series after the first stage, .002 µF. With the Response switch on Treble it cuts the bass to Direct Sig. and the second triode. On Bass the switch shorts it.
- Direct Sig., 100 kΩ pot, audio taper
- Direct Sig., 100 k. It sets how much dry guitar reaches A. Audio taper assumed.
- 50k, 50 kΩ
- From Direct Sig.’s wiper to A, 50 k.
- 150k, 150 kΩ
- Into the filter before the second triode, 150 k.
- .015µ, 15 nF
- The filter’s cap to ground, .015 µF. With the 150 k it cuts the treble.
- 120k, 120 kΩ
- From the filter to the second triode’s grid, 120 k.
- .0068µ, 6.8 nF
- Across the filter, .0068 µF, so the treble goes round it to the second triode. The drawing marks the value “(?)”.
- 1M, 1 MΩ
- The second triode’s grid resistor, 1 M.
- V1b, 12AX7 / ECC83 / 7025
- The second triode, the record amp for the top writing brush. A 12AX7 is assumed.
- 470k, 470 kΩ
- The second triode’s plate resistor, 470 k.
- 6.8k, 6.8 kΩ
- The second triode’s cathode resistor, 6.8 k.
- .068µ, 68 nF
- Across the second triode’s cathode resistor, .068 µF. It bypasses only above about 340 Hz, so this stage lifts the treble.
- .01µ, 10 nF
- From the second triode’s plate to the top writing brush’s preset, .01 µF.
- 2M preset, 2 MΩ pot, linear taper
- The top writing brush’s preset, 2 M, a trim inside. Its wiper feeds the brush. The drawing marks it as varying between units, 2 M in one and 7 M in the other (the 7 M build). Linear, set at half (assumed).
- Oil can, Oil can (Organ Tone disc, typical)
- The can holds a disc turning in oil, two writing brushes and a reading brush. The disc turns about 400 rpm, 6.7 times a second, and its speed swings once a turn, so the pitch of what it reads wavers about ±24 cents. The reading brush is 3 ms after the top writing brush. The bottom writing brush sits just past the reading brush, so what it writes comes round about 144 ms later. The charge leaks away in about 0.1 s. Every disc figure is assumed and can be changed.
- Motor, 10 V
- A stand-in, not a part of the unit. It puts 10 V across Motor Speed, so the knob can set how fast the disc turns.
- Motor Speed, 10 kΩ pot, linear taper
- Motor Speed, a stand-in for the motor’s speed, not a control on the unit. At half the disc turns 6.7 times a second, so the waver runs 6.7 times a second. At 0 the disc turns a fifth slower (5.4 times a second), full up a fifth faster (8 times a second). The motor needs about half a second to reach a new speed, so the pitch swoops as it gets there.
- .002µ, 2 nF
- From the reading brush to the follower’s grid, .002 µF.
- 4.6M, 4.6 MΩ
- The follower’s grid resistor, 4.6 M, to the tap between the 10 k and 6.8 k. The tap moves with the signal at the cathode, so very little signal current flows in the 4.6 M and the reading brush sees much more than 4.6 M.
- 10k, 10 kΩ
- The lower part of the follower’s cathode load, 10 k.
- 6.8k, 6.8 kΩ
- The upper part of the follower’s cathode load, 6.8 k. The voltage across it biases the grid.
- V2a, 12AX7 / ECC83 / 7025
- The third triode, a cathode follower. It reads the brush without loading it. A 12AX7 is assumed.
- 5µ, 5 µF electrolytic
- From the follower’s cathode to the echo node, 5 µF.
- Reverb Sustain, 1 MΩ pot, linear taper
- Reverb Sustain, 1 M. It sets how much of the reading brush goes to the fourth triode and back onto the disc at the bottom writing brush, so it sets the repeats. Linear taper assumed.
- V2b, 12AX7 / ECC83 / 7025
- The fourth triode, the record amp for the bottom writing brush. A 12AX7 is assumed.
- 470k, 470 kΩ
- The fourth triode’s plate resistor, 470 k.
- 6.8k, 6.8 kΩ
- The fourth triode’s cathode resistor, 6.8 k.
- 50µ, 50 µF electrolytic
- The fourth triode’s cathode bypass, 50 µF.
- .022µ, 22 nF
- From the fourth triode’s plate to Reverb Sig., .022 µF. The drawing marks the value “(?)”.
- Reverb Sig., 2 MΩ pot, linear taper
- Reverb Sig., 2 M. Its wiper feeds the bottom writing brush, so it sets how strongly the repeats are written. Linear taper assumed.
- 6.8k, 6.8 kΩ
- From the echo node to Organ-Tone Level, 6.8 k.
- .022µ, 22 nF
- To ground after the 6.8 k, .022 µF. Together they cut above about 1 kHz, which softens the disc’s grit.
- Organ-Tone Level, 25 kΩ pot, audio taper
- Organ-Tone Level, 25 k. It sets how much of the reading brush reaches A. Audio taper assumed.
- 50k, 50 kΩ
- From Organ-Tone Level’s wiper to A, 50 k.
- 50k, 50 kΩ
- From A to ground, 50 k. A is the Output jack.
- T, 125 V ac, 60 Hz
- The transformer’s secondary, as a sine at the mains frequency. Its voltage isn’t on the drawing, so 125 V is assumed.
- T R, 50 Ω
- The winding’s resistance. A typical value.
- D1, 1N4001
- One of the two rectifiers in series, half wave. A silicon part stands in for the drawing’s rectifier.
- D2, 1N4001
- The second rectifier in series. Two share the reverse voltage.
- 10µ, 10 µF electrolytic
- First filter cap, 10 µF.
- 10k, 10 kΩ
- First dropping resistor, 10 k.
- 20µ, 20 µF electrolytic
- Second filter cap, 20 µF.
- 10k, 10 kΩ
- Second dropping resistor, 10 k.
- 20µ, 20 µF electrolytic
- Filter cap on B+, 20 µF. B+ feeds all four triodes.
Versions
- 2 M preset
- Jamie Ray’s drawing, with the top writing brush’s preset at 2 M, one of the two units he read. The tubes, the winding and the can’s figures are assumed.
- 7 M preset
- The other unit on the drawing, with a 7 M preset feeding the top writing brush. The tubes, the winding and the can’s figures are assumed.
Sources
- Jamie Ray, redrawn Deluxe Organ Tone schematic, 2002
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.