Stereo amp with two pairs of 6BQ5s and grid tremolo, 1960 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Gibson GA-78.
Two channels, each with its own preamp, cathodyne and pair of cathode-biased 6BQ5s. The bench draws one side: two 6EU7 stages with a tone network between them, into a cathodyne with no driver. The tremolo swings both output grids through their grid leaks.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for One channel of a stereo amp. After the first 6EU7 stage the signal reaches the top of the Volume pot two ways. The treble goes through 250 pF, and the rest through two 150 kΩ resistors. The Tone pot runs from that top to ground with its wiper between the two resistors, where a .01 µF cap goes to ground. Turned toward the ground end, it pulls the middle point down and only the 250 pF path is left, so the sound gets thinner and brighter. Turned the other way, the .01 µF cuts the treble at the Volume pot. The second 6EU7 stage feeds a cathodyne through 500 pF, into two 6BQ5s on one 200 Ω cathode resistor with no feedback. The tremolo oscillator is a third 6EU7. Its swing goes through the Depth pot to the point where both output grids’ 220 kΩ leaks meet. The bench leaves out the second channel, which is the same circuit on its own speaker, and the Stereo/Mono switch.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 51k, 51 kΩ
- From the input jack to V1’s grid. Each of the channel’s two jacks has its own 51 kΩ to the grid, so either one sounds the same.
- 1M, 1 MΩ
- Grid resistor for V1, the grid’s path to ground.
- V1a, 6EU7
- One half of a 6EU7, the input stage, cathode bypassed for full gain. The other half is channel 2’s.
- 100k, 100 kΩ
- Plate resistor for V1. The drawing reads +185 V on the plate.
- 2.2k, 2.2 kΩ
- Cathode resistor for V1, +1.4 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V1’s cathode resistor.
- .02µ, 20 nF
- Coupling cap from V1 to the tone network.
- 250p, 250 pF
- The treble path, 250 pF straight to the top of the Volume pot, around the two 150 kΩ resistors.
- 150k, 150 kΩ
- First of the two 150 kΩ resistors from the coupling cap to the top of the Volume pot. The Tone pot’s wiper and the .01 µF meet between them.
- 150k, 150 kΩ
- Second 150 kΩ, from the Tone pot’s wiper to the top of the Volume pot.
- .01µ, 10 nF
- From the point between the two 150 kΩ resistors to ground. It bleeds treble from the resistor path.
- Tone 2M, 2 MΩ pot, reverse audio taper
- Tone, 2 MΩ reverse audio, from the top of the Volume pot to ground with its wiper between the two 150 kΩ resistors. Turned up, the wiper moves toward ground, the resistor path is pulled down and the 250 pF treble path is left, so the sound is brighter and thinner. Turned down, the wiper moves toward the Volume pot and the .01 µF cuts the treble there. Up is assumed to be brighter.
- Vol 1M, 1 MΩ pot, audio taper
- Volume, 1 MΩ audio. Its wiper is V2’s grid. There’s no master, so it sets how hard everything after it is pushed.
- V2a, 6EU7
- One half of a 6EU7, the second gain stage, cathode bypassed. The other half is channel 2’s.
- 100k, 100 kΩ
- Plate resistor for V2. The drawing reads +180 V on the plate.
- 2.2k, 2.2 kΩ
- Cathode resistor for V2, +1.45 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V2’s cathode resistor.
- 500p, 500 pF
- Only 500 pF into the inverter’s grid. The cathodyne’s grid resistor returns to its own cathode, so the grid looks like several megohms and 500 pF still passes the guitar’s range.
- 270k, 270 kΩ
- Plate resistor for the oscillator, from the +275 V node. The drawing reads +122 V on the plate.
- V3, 6EU7
- One half of a 6EU7, the tremolo oscillator. The drawing shows the other half unused.
- 1k, 1 kΩ
- Cathode resistor for the oscillator, +.85 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for the oscillator’s cathode.
- .03µ, 30 nF
- First cap of the oscillator’s phase-shift ladder.
- 68k, 68 kΩ
- In series with the Frequency pot, the ladder’s first leg. It sets the top speed.
- Freq, 500 kΩ pot, reverse audio taper
- Frequency, 500 kΩ reverse audio, as a variable resistor in the ladder’s first leg. Turned up, its resistance drops and the oscillator runs faster. Its far end goes through the foot switch to ground.
- .02µ, 20 nF
- Second ladder cap.
- 510k, 510 kΩ
- Second ladder leg to ground.
- .02µ, 20 nF
- Third ladder cap, into the grid. At one frequency the three caps and legs turn the plate’s swing upside down by the time it reaches the grid, so the stage oscillates at that frequency.
- 1.5M, 1.5 MΩ
- Grid leak for the oscillator, and the ladder’s last leg.
- .03µ, 30 nF
- Couples the oscillator’s swing from its plate to the Depth pot and blocks the plate’s DC.
- Depth, 250 kΩ pot, reverse audio taper
- Depth, 250 kΩ reverse audio, from the cap to ground. Its wiper is where the output tubes’ two grid leaks meet, in both channels, so it sets how much of the swing reaches the grids. Turned up, more of it does. On Preamp only, the wiper drives nothing.
- V6a, 6EU7
- 6EU7, a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 47k, 47 kΩ
- The cathodyne’s plate resistor, the output to tube B.
- 1.5k, 1.5 kΩ
- The cathodyne’s bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 47k, 47 kΩ
- The cathodyne’s cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470 kΩ
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathode’s high DC voltage. It’s the grid’s only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ω.
- .02µ, 20 nF
- Coupling cap to tube A’s grid.
- .02µ, 20 nF
- Coupling cap to tube B’s grid.
- 1.5k, 1.5 kΩ
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current.
- 1.5k, 1.5 kΩ
- Grid stopper for tube B.
- V4, EL84 / 6BQ5 (Philips curves)
- EL84, tube A of the push-pull pair, its cathode on the shared cathode resistor, so it biases itself.
- V5, EL84 / 6BQ5 (Philips curves)
- EL84, tube B of the pair.
- 220k, 220 kΩ
- Grid leak for tube A, returned with tube B’s to the tremolo’s Depth pot, so the oscillator swings both grids together. The bias comes from the cathode resistor. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 220k, 220 kΩ
- Grid leak for tube B.
- 200, 200 Ω
- The shared cathode resistor. Every output tube’s current runs through it and lifts the cathodes above the grids, and that’s the bias. Driven hard, the pair draws more current on average, so the cathodes climb and the tubes run colder, which softens the clipping.
- 20µ, 20 µF electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 3 H, 3 H
- The choke from the reservoir cap to B+, as on the amp’s drawing. The output transformer’s center tap, the screens and everything after them hang past it, so all of their current runs through it. It passes DC with little drop. With the cap after it, it would filter ripple, but ripple isn’t modeled here. Typical of the part.
- 80, 80 Ω
- The choke’s winding resistance, typical. With the output tubes’ whole current through it, it’s most of the DC drop between the reservoir and B+.
- 20µ, 20 µF electrolytic
- Filter cap on B+ after the choke, where the output transformer’s center tap and the screens hang.
- 10k, 10 kΩ
- Dropping resistor from the screen supply node to the node for both inverters and the tremolo, as on the Gibson GA-78 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20µ, 20 µF electrolytic
- Filter cap at the node for both inverters and the tremolo. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 10k, 10 kΩ
- Dropping resistor from the node for both inverters and the tremolo to the node for both preamps, as on the Gibson GA-78 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 20µ, 20 µF electrolytic
- Filter cap at the node for both preamps. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- Ch. 2 6BQ5s, 5 kΩ
- Stands for channel 2’s pair of 6BQ5s (not drawn) on the screen supply node. It pulls about the current worked out from the voltages on the drawing. That part of the amp isn’t modeled here. A typical value.
- Ch. 2 inverter, 260 kΩ
- Stands for channel 2’s cathodyne (not drawn) on the node for both inverters and the tremolo. It pulls about the current worked out from the voltages on the drawing. That part of the amp isn’t modeled here. A typical value.
- Ch. 2 preamp, 190 kΩ
- Stands for channel 2’s preamp (not drawn) on the node for both preamps. It pulls about the current worked out from the voltages on the drawing. That part of the amp isn’t modeled here. A typical value.
- OT, 8 kΩ to 8 Ω, 40 H primary, 10 mH leakage
- The output transformer, 8 kΩ plate to plate into 8 Ω, center tap on B+ after the choke. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 258 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 258 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 258 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 25 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 25 Ω
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 20µ, 20 µF electrolytic
- The reservoir cap. It feeds the choke, and past it the output transformer’s center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 8.69 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 8 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 464 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 2.19 Ω
- Limits what Loss L2 adds.
- Tank R, 83.7 Ω
- Height of the bass resonance, about 92 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 21.1 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- Channel 1 of the stereo amp, as on the factory drawing. Channel 2 is the same circuit.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.