OTA envelope filter, 1976 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Mu-Tron Micro V.
An auto-wah built on one OTA. The guitar’s peaks set the current into the OTA’s bias pin, and the filter’s resonant peak moves up with it. Range sets how hard you have to play. A switch moves the whole sweep down.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 buffers the guitar. The filter is one CA3080 OTA, an amplifier whose output current follows its input voltage, and one op-amp integrator, IC2B. The current into the OTA’s bias pin sets how much current it delivers for each millivolt in. IC2B’s output feeds back to the OTA’s input through R7, and that feedback makes a resonant peak about 20 dB over the guitar’s level. The peak moves with the square root of the bias current, so four times the current moves it up an octave. R14 feeds about 8 µA at rest, and the peak rests near 260 Hz on Hi and 105 Hz on Lo. IC2A rectifies the guitar and pulls C12 down through R12 in a few milliseconds. Once C12 is about 0.6 V under VB, Q2 adds its current. A steady A4 at 200 mV puts about 350 µA into the bias pin, so the peak moves near 1.7 kHz on Hi and 690 Hz on Lo. On a plucked A2 the current climbs to about 260 µA in a tenth of a second and falls back as the note dies. Range sets the rectifier’s gain, from about 1.5 to 68. The values follow a later redraw, with its additions left out. The footswitch isn’t on it, so bypass to the input jack is assumed.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R16, 22 kΩ
- Top of the divider that sets VB.
- R17, 33 kΩ
- Bottom of the divider. With R16 it puts 5.4 V on Q3’s base.
- Q3, 2N5088
- An emitter follower. Its emitter is VB, about 4.8 V, the reference the signal parts return to.
- R18, 100 kΩ
- Q3’s emitter load.
- C13, 100 µF electrolytic
- Holds VB steady.
- C1, 100 nF
- Input coupling cap.
- R1, 100 kΩ
- In series with Q1’s base. With C2 it trims radio pickup.
- R2, 100 kΩ
- Holds Q1’s base at VB.
- C2, 100 pF
- Rolls off radio frequencies at the input.
- Q1, 2N5088
- The input buffer, an emitter follower. It feeds the filter and the envelope from a low impedance.
- R3, 10 kΩ
- Q1’s emitter load.
- C3, 47 nF
- Feeds the guitar into the OTA’s + input.
- R5, 330 Ω
- From the OTA’s + input to VB. It keeps the signal there small, a few tens of millivolts, so the OTA stays clean.
- R6, 330 Ω
- Across R5 with the switch on Lo, halving the signal into the OTA.
- IC1, CA3080
- A CA3080, the filter’s tuning part. Its output current is its input voltage times a gain set by the current into its bias pin. More current tunes the filter higher.
- C4, 33 nF
- Feeds the guitar straight to the OTA’s output as well.
- C5, 68 nF
- On Lo, from the OTA’s output to VB. The OTA has to charge it, so the filter tunes lower.
- R8, 47 kΩ
- Carries the OTA’s output into IC2B.
- C8, 2.2 nF
- From IC2B’s − input to VB.
- IC2B, MC1458
- Half of an LM1458, an integrator. Its output is the filter’s output.
- C9, 1.8 nF
- IC2B’s integrator cap. With the OTA it sets the filter’s frequency.
- R7, 6.8 kΩ
- Feeds the output back into the OTA’s + input. With R5 it sets how tall the peak is.
- C7, 2.2 nF
- Across R7. It feeds back more of the treble.
- C10, 10 µF electrolytic
- Output coupling cap.
- R9, 22 kΩ
- Holds the output at 0 V DC.
- C11, 4.7 µF electrolytic
- Feeds Q1’s output to the envelope side.
- R10, 15 kΩ
- IC2A’s input resistor.
- IC2A, MC1458
- The other half of the LM1458, a rectifier. On each upward half of the guitar its output swings down and pulls C12 with it.
- D2, 1N914 / 1N4148
- Clamps IC2A’s output about 0.6 V over VB on the other half.
- D3, 1N914 / 1N4148
- Lets IC2A pull C12 down, never up.
- R11, 22 kΩ
- In series with Range in IC2A’s feedback. With Range at 0 the gain is about 1.5.
- Range, 1 MΩ pot, linear taper
- Range, 1 MΩ linear, a variable resistor in IC2A’s feedback. Clockwise the rectifier’s gain rises, up to about 68, so softer playing moves the filter further.
- R12, 680 Ω
- The attack. C12 charges through it in a few milliseconds.
- C12, 4.7 µF electrolytic
- The envelope cap. It charges below VB as you play.
- R13, 47 kΩ
- The decay. C12 drains back to VB through it.
- Q2, 2N5087
- A 2N5087 (PNP). Once C12 falls about 0.6 V under VB it conducts, and its collector current goes into the OTA’s bias pin.
- R15, 4.7 kΩ
- Sets Q2’s current, the envelope’s voltage minus 0.6 V over 4.7 kΩ.
- R14, 1 MΩ
- Feeds the bias pin about 8 µA from 9 V, so the filter has a resting frequency.
About this version
- Stock
- Negative ground, 9 V, a 4.8 V reference from Q3. A CA3080 OTA and an LM1458.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.