Through-zero flanger on two delay chips, bench design
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
This one is a bench design, because no 1970s pedal that did this could be confirmed. Two MN3007 delay chips hold the guitar about 2.5 ms behind, line 1 on a fixed clock and line 2 swept past it. Line 2 is inverted before the two are added, so where the delays cross they cancel. That is the through-zero point.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Through-zero flanging started in the studio, with two tape machines playing the same track and one slowed by hand against the other. With one machine’s output inverted, the two cancel where their delays match. This pedal does the same with two bucket-brigade lines. IC1a buffers the guitar, and IC1b, a low-pass near 7.9 kHz, feeds both MN3007s from one output. Line 1’s clock holds at about 206 kHz, a delay of 2.49 ms. At full Depth line 2’s clock runs from 0.70 to 1.30 times line 1’s, a delay of 3.56 down to 1.92 ms, so line 2 starts behind line 1, passes it and ends ahead. IC7a inverts line 2 and IC7b adds the two. Where the delays match they cancel at every frequency. Away from the crossing they cut a row of notches, and with one line inverted the lowest notes cancel too, so the sound thins out near the crossing. Manual moves the crossing through the sweep, and at Depth 0 with Manual at about 0.51 the delays hold equal, and a steady low A comes out about 65 dB under the dry level. Balance sets line 2’s level against line 1’s. Off the middle, the part that doesn’t cancel fills the null. The low-pass filters have to match in the same way. Both lines share the one ahead of the chips, and each line has a separate one after its chip. With C9 at 3.3 nF in place of 2.7 nF, the null at 3 kHz fills in from about 47 to about 30 dB under the dry level, while the lows stay cancelled. The Dry switch adds the dry signal as a third copy. Rate runs the sweep from about 0.1 to 1.1 times a second. The real MN3101 runs from an RC network on its pins. The model runs it from the timing pin’s current, so R16’s current moves line 2’s clock. The bypass switch, the LED and the chips’ supply pins aren’t drawn.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C20, 100 µF electrolytic
- Bulk cap across the 9 V supply.
- R1, 10 kΩ
- Top of the 4.5 V bias divider for the audio.
- R2, 10 kΩ
- Bottom of the bias divider.
- C2, 47 µF electrolytic
- Filters the 4.5 V bias line.
- C1, 47 nF
- Input coupling cap.
- R3, 1 MΩ
- Biases IC1a at 4.5 V and sets the input impedance near 1 MΩ.
- IC1a, RC4558
- Input buffer, a follower. Its output is also the dry signal.
- R4, 10 kΩ
- First resistor of the low-pass ahead of the delay chips.
- R5, 10 kΩ
- Second resistor of the low-pass.
- C3, 2.7 nF
- Feedback cap of the low-pass, from IC1b’s output.
- C4, 1.5 nF
- With C3, R4 and R5 it makes a two-pole low-pass near 7.9 kHz, twice as steep as one resistor and cap, so the clocks don’t fold high notes back down.
- IC1b, RC4558
- Follower of the low-pass. It drives both delay chips from one output, so both lines start with the same signal.
- IC2, MN3007
- Line 1, an MN3007, 1024 stages. It passes each sample on after 512 clock periods. Its two outputs are drawn as one pin.
- IC3, MN3101
- Line 1’s MN3101 clock, with a 100 pF timing cap. R14 by itself sets it, about 205 kHz, so line 1 holds still at about 2.5 ms.
- R14, 22 kΩ
- Line 1’s timing resistor.
- R6, 47 kΩ
- Load on line 1’s outputs.
- C5, 100 nF
- Couples line 1 into its low-pass.
- R7, 100 kΩ
- Holds line 1’s low-pass at 4.5 V.
- R8, 10 kΩ
- First resistor of line 1’s low-pass.
- R9, 10 kΩ
- Second resistor of line 1’s low-pass.
- C6, 2.7 nF
- Feedback cap of line 1’s low-pass.
- C7, 1.5 nF
- Line 1’s low-pass, the same as the one ahead of the chips. It smooths the chip’s steps.
- IC6a, RC4558
- Follower of line 1’s low-pass.
- IC4, MN3007
- Line 2, an MN3007, the same as line 1. Its noise is independent of line 1’s, as with two real chips.
- IC5, MN3101
- Line 2’s MN3101 clock, the same as line 1’s. The current through R16 speeds it up or slows it down, from 0.70 to 1.30 times line 1’s clock at full Depth.
- R15, 22 kΩ
- Line 2’s timing resistor, equal to R14, so the two clocks match with the control at 4.5 V.
- R16, 22 kΩ
- From the clock control into line 2’s timing pin. A smaller value makes every sweep wider.
- R10, 47 kΩ
- Load on line 2’s outputs.
- C8, 100 nF
- Couples line 2 into its low-pass.
- R11, 100 kΩ
- Holds line 2’s low-pass at 4.5 V.
- R12, 10 kΩ
- First resistor of line 2’s low-pass.
- R13, 10 kΩ
- Second resistor of line 2’s low-pass.
- C9, 2.7 nF
- Feedback cap of line 2’s low-pass. If it differs from C6, the two lines differ in the treble and the null fills in there.
- C10, 1.5 nF
- Line 2’s low-pass, the same as line 1’s.
- IC6b, RC4558
- Follower of line 2’s low-pass.
- R17, 10 kΩ
- Input resistor of the inverting stage.
- R18, 5.1 kΩ
- Feedback resistor, in series with Balance. It sets the least gain, 0.51.
- Balance, 10 kΩ pot, linear taper
- Balance, 10 kΩ linear, used as a variable resistor. It sets line 2’s level against line 1’s, from 0.51 to 1.51 times. Near the middle the two match and cancel fully where the delays cross.
- IC7a, RC4558
- Inverting stage. It turns line 2 upside down, so line 2 cancels line 1 where their delays match.
- R19, 10 kΩ
- Mixing resistor for line 1.
- R20, 10 kΩ
- Mixing resistor for line 2, inverted.
- R21, 10 kΩ
- Mixing resistor for the dry signal, through the Dry switch.
- R22, 10 kΩ
- Feedback resistor of the mixer. Each input comes through at a gain of 1.
- C11, 100 pF
- Across R22. Rolls the top end off above about 160 kHz, so the mixer stays quiet.
- IC7b, RC4558
- Mixer. It adds line 1 and line 2 inverted, and the dry signal with the Dry switch on.
- C12, 1 µF electrolytic
- Output coupling cap.
- Level, 100 kΩ pot, audio taper
- Level, 100 kΩ audio. Its wiper is the output.
- R24, 10 kΩ
- Top of the LFO’s 4.5 V divider.
- R25, 10 kΩ
- Bottom of the LFO’s 4.5 V divider.
- C13, 47 µF electrolytic
- Filters the LFO’s 4.5 V line.
- IC8a, RC4558
- Comparator with hysteresis, which means it switches at one level on the way up and a different one on the way down. Its output flips to the other rail each time the triangle reaches a turn, so it puts out a square wave.
- R26, 47 kΩ
- Positive feedback that holds the comparator where it last flipped.
- R27, 33 kΩ
- From the triangle to the comparator. Against R26 it sets the triangle’s height.
- Rate, 100 kΩ pot, linear taper
- Rate, 100 kΩ linear. It sets how much of the square reaches the integrator, and that sets how fast the triangle ramps, about 0.1 to 1.1 sweeps a second.
- R28, 10 kΩ
- Under Rate, to IC9b’s 4.5 V. It sets the slowest sweep.
- R29, 1 MΩ
- Integrator input resistor. With C14 it sets the ramp’s speed.
- C14, 330 nF
- Integrator cap. A smaller cap makes every Rate setting faster.
- IC8b, RC4558
- Integrator. The square wave in makes a triangle out.
- Depth, 100 kΩ pot, linear taper
- Depth, 100 kΩ linear. It sets how much of the triangle reaches line 2’s clock, and that sets how far line 2’s delay swings past line 1’s, 3.56 to 1.92 ms at full. At 0 the delays hold still.
- R30, 56 kΩ
- Depth’s share of the clock control.
- Manual, 100 kΩ pot, linear taper
- Manual, 100 kΩ linear, across the supply. It moves the middle of line 2’s sweep, from 3.44 ms at 0 to 1.96 ms at full. At about 0.51 the two delays cross in the middle of the sweep.
- R31, 120 kΩ
- Manual’s share of the clock control.
- R32, 33 kΩ
- Feedback resistor of the control stage.
- C15, 100 nF
- Across R32. It rounds the triangle’s corners off (about 48 Hz).
- IC9b, LM358
- Follower on the LFO’s 4.5 V. The Rate and Depth pots and IC9a work from its output, so their currents don’t move the 4.5 V line with the sweep.
- IC9a, LM358
- Clock control, half an LM358. It adds Depth and Manual around 4.5 V and inverts the sum. Its output through R16 sets line 2’s clock.
About this version
- Bench design
- Negative ground, 9 V. The audio works around the 4.5 V from R1 and R2. The LFO and the clock control work around a separate 4.5 V from R24 and R25, buffered by IC9b.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.