6SJ7 into a 6SN7 paraphase with plate feedback, about 1950
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Gibson BR-6F.
Three jacks into one 6SJ7 pentode and a volume knob. A 6SN7 paraphase drives two cathode-biased 6V6s, with 470 kΩ from each 6V6’s plate back to the 6SN7 plate that drives it. The speaker’s field coil is the supply’s choke.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar goes in through 100 kΩ. With nothing in the other two jacks, their switches ground their tips, so their 100 kΩ resistors put 50 kΩ from the grid to ground. About two thirds of the guitar’s level is lost there, before the 6SJ7. The 6SJ7 runs on a 2.2 MΩ screen resistor and a 220 kΩ plate resistor, and feeds the 500 kΩ Volume. The Volume’s wiper is the 6SN7’s first grid. That half drives one 6V6. A 100 kΩ and 10 kΩ divider under that 6V6’s grid feeds the second half, which drives the other 6V6. Each 6SN7 plate also has 470 kΩ from the 6V6 plate it drives. The 6V6 plate swings the opposite way, so this is negative feedback on each side. It lowers the gain and the distortion. There’s no feedback from the speaker. The speaker’s field coil, 1000 Ω, is the filter choke. The drawing is a 1960 redraw, and one wire crossing near the 6SN7 has no hop drawn. It’s read as a crossing, since the inverter only works that way. The transformer figures are typical for the size.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 100k, 100 kΩ
- Jack 1’s 100 kΩ to the grid.
- 100k, 100 kΩ
- Jack 2’s 100 kΩ. With nothing in jack 2, its switch grounds the tip, so this resistor goes from the grid to ground.
- 100k, 100 kΩ
- Jack 3’s 100 kΩ, grounded the same way. With R2 it puts 50 kΩ from the grid to ground. That is the grid’s only path to ground, and with the 100 kΩ from jack 1 it divides the guitar’s level to about a third.
- V1, 6SJ7
- 6SJ7 pentode, the amp’s one preamp stage. Its suppressor is tied to the cathode.
- 2.2k, 2.2 kΩ
- Cathode resistor for V1.
- 20µ, 20 µF electrolytic
- Bypass for V1’s cathode resistor, full gain down to a few hertz.
- 2.2M, 2.2 MΩ
- Screen resistor, 2.2 MΩ. It holds the screen low, so the plate current is small.
- .05µ, 50 nF
- Screen bypass cap.
- 220k, 220 kΩ
- Plate resistor for V1.
- .01µ, 10 nF
- Coupling cap to the volume. With the 500 kΩ pot it passes everything above about 30 Hz.
- Vol 500k, 500 kΩ pot, audio taper
- Volume, 500 kΩ. Its wiper is the 6SN7’s first grid, and the pot is that grid’s path to ground. The drawing marks no taper, so audio is assumed.
- V2a, 6SN7
- 6SN7, the first half of the paraphase inverter. It’s a plain gain stage: its plate swings opposite the input and drives tube A. Its grid connects straight to the preamp’s output with no coupling cap, so its path to ground is through the preamp’s volume and tone network.
- 100k, 100 kΩ
- Plate resistor for the first half, the output to tube A.
- 3.3k, 3.3 kΩ
- Cathode resistor for both halves. The tube has one cathode for its two triodes, so this carries both currents and sets both biases.
- 100k, 100 kΩ
- Tube A’s grid resistor, down to the tap. With the resistor under the tap it feeds a small share of tube A’s grid signal to the second half’s grid. The share is about one over the second half’s gain, so the two output grids swing about the same.
- 10k, 10 kΩ
- The tap, 10k Ω to ground under tube A’s grid resistor, and the second half’s grid resistor. The two sides only match while the share times the second half’s gain is 1, so they drift apart as the tube ages.
- V2b, 6SN7
- The second half. It turns the divided signal over again, so its plate swings with the input. It drives tube B.
- 100k, 100 kΩ
- Plate resistor for the second half, the output to tube B.
- 470k, 470 kΩ
- Feedback, 470k Ω from tube A’s plate back to the first half’s plate, which drives tube A. The output plate swings the opposite way to the drive, so this lowers the output stage’s gain and its output impedance, which steadies the speaker. It doesn’t reach around the output transformer.
- 470k, 470 kΩ
- The same from tube B’s plate back to the second half’s plate.
- .05µ, 50 nF
- Coupling cap to tube A’s grid.
- .05µ, 50 nF
- Coupling cap to tube B’s grid.
- V3, 6V6GT
- 6V6GT, tube A of the push-pull pair, its cathode on the shared cathode resistor, so it biases itself.
- V4, 6V6GT
- 6V6GT, tube B of the pair.
- 100k, 100 kΩ
- Grid leak for tube B.
- 200, 200 Ω
- The shared cathode resistor. Every output tube’s current runs through it and lifts the cathodes above the grids, and that’s the bias. Driven hard, the pair draws more current on average, so the cathodes climb and the tubes run colder, which softens the clipping.
- 4 H, 4 H
- The speaker’s field coil, which is also the supply’s filter choke. The current through it makes the speaker’s magnet. That current feeds everything after the coil: the output tubes, the 6SN7 and the 6SJ7. Its inductance, 4 H, is typical, not on the drawing.
- 1k, 1 kΩ
- The field coil’s resistance, 1000 Ω, from the drawing. All of the amp’s current runs through it.
- 10µ, 10 µF electrolytic
- Filter cap on B+ after the choke, where the output transformer’s center tap and the screens hang.
- 47k, 47 kΩ
- Dropping resistor from the screen supply node to the node for the inverter and preamp, as on the Gibson BR-6F drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 10µ, 10 µF electrolytic
- Filter cap at the node for the inverter and preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 8 kΩ to 8 Ω, 10 H primary, 10 mH leakage
- The output transformer, 8 kΩ plate to plate into 8 Ω, center tap on B+ after the choke. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 315 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 315 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 315 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 60 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 60 Ω
- Resistance of the other half. Typical of the part.
- V5, 5Y3GT
- One plate of the 5Y3GT rectifier. It conducts near the peak of its half of the winding, and its own drop rises with the current, which adds to the sag.
- V5, 5Y3GT
- The rectifier’s other plate, on the other half cycle.
- 20µ, 20 µF electrolytic
- The reservoir cap. It feeds the choke, and past it the output transformer’s center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 8.69 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 8 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 464 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 2.19 Ω
- Limits what Loss L2 adds.
- Tank R, 83.7 Ω
- Height of the bass resonance, about 92 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 21.1 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The 6SN7 and 6V6 are the bench’s models. The transformers and the field coil’s inductance are typical, not on the drawing.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.