Two-channel EL84 reverb amp with lamp tremolo, mid 1960s style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Gibson GA-20RVT Minuteman.
Two 6EU7 channels, each with bass, treble and loudness and a second stage, mixed into a 12AU7 that drives a transformer into two cathode-biased EL84s. The Reverb channel has the springs and a tremolo, a lamp beside a photocell on its second grid.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each channel starts on one half of a 6EU7 and goes through a small coupling cap into its tone controls. Treble is a 2 MΞ© pot in series with .01 Β΅F to ground. Bass is a 2 MΞ© pot under a 68 kΞ© and .022 Β΅F. Loudness feeds two 220 kΞ© with .0047 Β΅F from their middle to ground and 330 pF across both. That makes a notch in the low mids before the second 6EU7 stage. The two channels meet through 1.5 MΞ© and 1 MΞ©, pass a second notch of the same kind, and reach V5a, a 12AU7. V5a drives a transformer whose center-tapped secondary feeds both EL84 grids in opposite phase, with no coupling caps. The two EL84s run on 130 Ξ© with 20 Β΅F and no feedback. Only the Reverb channel feeds the springs, and the reverb comes back into that channelβs second stage. The tremolo works on the Reverb channel too. An oscillator swings the current through a small bulb, and a photocell beside the bulb pulls the second stageβs grid down as the bulb brightens. The bulb glows dimly even with the tremolo off, so the cell loads the Reverb channel slightly at rest. At full Depth a steady A4 rises and falls about 14 dB, 3 to 8 times a second. Low notes swing less, since the cell pulls through .022 Β΅F. The springs are a measured tank, played from its impulse response, a recording of how the real springs ring after a click. The transformer figures are typical for the size.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R1, 68βkΞ©
- Input 1βs resistor, 68 kΞ©. With nothing in input 2 the two 68 kΞ© are in parallel, so input 1 reaches the channel through 34 kΞ©. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- R2, 68βkΞ©
- Input 2βs resistor, 68 kΞ©. With nothing in input 1 that jack grounds input 1βs tip, so the two 68 kΞ© make a divider and input 2 is about 6 dB quieter. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- R20, 68βkΞ©
- Input 1βs resistor, 68 kΞ©. With nothing in input 2 the two 68 kΞ© are in parallel, so input 1 reaches the channel through 34 kΞ©. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- R21, 68βkΞ©
- Input 2βs resistor, 68 kΞ©. With nothing in input 1 that jack grounds input 1βs tip, so the two 68 kΞ© make a divider and input 2 is about 6 dB quieter. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- .0047Β΅, 4.7βnF
- Input coupling cap, .0047 Β΅F. With the 470 kΞ© after it, it cuts below about 70 Hz.
- 470k, 470βkΞ©
- Grid resistor for the first stage.
- V1b, 6EU7
- One half of V1, a 6EU7, the Normal channelβs first stage.
- 100k, 100βkΞ©
- Plate resistor for V1b. The drawing reads +150 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V1b, +1.2 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V1bβs cathode resistor. Its value isnβt printed on the drawing, so 20 Β΅F is assumed.
- .0047Β΅, 4.7βnF
- Coupling cap to the tone node, .0047 Β΅F. Itβs half the Reverb channelβs .01 Β΅F, so this channel has less bass ahead of the tone controls.
- 68k, 68βkΞ©
- From the tone node to the bass network.
- .022Β΅, 22βnF
- The bass networkβs cap. With the Bass pot turned up, the 68 kΞ© reaches ground mostly through this cap, which passes treble far more easily than bass.
- Bass, 2βMΞ© pot, reverse audio taper
- Bass, 2 MΞ© reverse audio, as a variable resistor from the bass network to ground. At 0 the 68 kΞ© goes straight to ground and loads every frequency. Turned up, its resistance rises and the load goes through the .022 Β΅F, which bleeds more treble than bass, so the bass comes up relative to the rest.
- Treble, 2βMΞ© pot, audio taper
- Treble, 2 MΞ© audio, as a variable resistor from the tone node to the .01 Β΅F. Turned up, its resistance rises, less treble goes to ground and the channel gets brighter.
- .01Β΅, 10βnF
- The treble cap, to ground through the Treble pot.
- Loudness, 250βkΞ© pot, audio taper
- Loudness, 250 kΞ© audio, the channelβs volume, from the tone node to ground. Its wiper feeds the filter into the second stage.
- 220k, 220βkΞ©
- First half of the filter into the second stage.
- .0047Β΅, 4.7βnF
- From the middle of the two 220 kΞ© to ground. With the 330 pF across both it makes a notch in the low mids, near 500 Hz.
- 220k, 220βkΞ©
- Second half of the filter, into the second stageβs grid.
- 330p, 330βpF
- Across both 220 kΞ©. It carries the treble past the filter.
- V4b, 6EU7
- One half of V4, a 6EU7, the Normal channelβs second stage.
- 100k, 100βkΞ©
- Plate resistor for V4b. The drawing reads +150 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V4b, +1.2 V on the drawing.
- .22Β΅, 220βnF
- Only .22 Β΅F across the 1.5 kΞ©, so the stage has its full gain only from about 1 kHz up. Below that the gain falls back by about half, so the bass is held down here.
- 1.5M, 1.5βMΞ©
- Mixing resistor from V4bβs plate to the node where both channels meet. Into the 220 kΞ© past the .01 Β΅F itβs a divider, about 18 dB down.
- .0047Β΅, 4.7βnF
- Input coupling cap, .0047 Β΅F. With the 470 kΞ© after it, it cuts below about 70 Hz.
- 470k, 470βkΞ©
- Grid resistor for the first stage.
- V1a, 6EU7
- One half of V1, a 6EU7, the Reverb channelβs first stage.
- 100k, 100βkΞ©
- Plate resistor for V1a. The drawing reads +154 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V1a, +1.2 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V1aβs cathode resistor. Its value isnβt printed on the drawing, so 20 Β΅F is assumed.
- .01Β΅, 10βnF
- Coupling cap to the tone node, .01 Β΅F.
- 68k, 68βkΞ©
- From the tone node to the bass network.
- .022Β΅, 22βnF
- The bass networkβs cap. With the Bass pot turned up, the 68 kΞ© reaches ground mostly through this cap, which passes treble far more easily than bass.
- Bass, 2βMΞ© pot, reverse audio taper
- Bass, 2 MΞ© reverse audio, as a variable resistor from the bass network to ground. At 0 the 68 kΞ© goes straight to ground and loads every frequency. Turned up, its resistance rises and the load goes through the .022 Β΅F, which bleeds more treble than bass, so the bass comes up relative to the rest.
- Treble, 2βMΞ© pot, audio taper
- Treble, 2 MΞ© audio, as a variable resistor from the tone node to the .01 Β΅F. Turned up, its resistance rises, less treble goes to ground and the channel gets brighter.
- .01Β΅, 10βnF
- The treble cap, to ground through the Treble pot.
- Loudness, 500βkΞ© pot, audio taper
- Loudness, 500 kΞ© audio, the channelβs volume, from the tone node to ground. Its wiper feeds the filter into the second stage.
- 220k, 220βkΞ©
- First half of the filter into the second stage.
- .0047Β΅, 4.7βnF
- From the middle of the two 220 kΞ© to ground. With the 330 pF across both it makes a notch in the low mids, near 500 Hz.
- 220k, 220βkΞ©
- Second half of the filter, into the second stageβs grid.
- 330p, 330βpF
- Across both 220 kΞ©. It carries the treble past the filter.
- V4a, 6EU7
- One half of V4, a 6EU7, the Reverb channelβs second stage. The reverb comes in on its grid, and the tremoloβs photocell pulls its grid down.
- 100k, 100βkΞ©
- Plate resistor for V4a. The drawing reads +175 V on the plate.
- 3.3k, 3.3βkΞ©
- Cathode resistor for V4a, +1.7 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V4aβs cathode resistor. Its value isnβt printed on the drawing, so 20 Β΅F is assumed.
- 1M, 1βMΞ©
- Mixing resistor from V4aβs plate to the node where both channels meet. Into the 220 kΞ© past the .01 Β΅F itβs a divider, about 15 dB down.
- .01Β΅, 10βnF
- Coupling cap from the mixing node.
- 220k, 220βkΞ©
- To ground past the .01 Β΅F. With the 1.5 MΞ© and 1 MΞ© mixing resistors it sets how much of each channel gets through.
- 220k, 220βkΞ©
- First half of the filter into V5a.
- .0047Β΅, 4.7βnF
- From the middle of the two 220 kΞ© to ground. With the 330 pF across both it makes a second low-mid notch, after the one in each channel.
- 220k, 220βkΞ©
- Second half of the filter, into V5aβs grid. These three 220 kΞ© are V5aβs path to ground.
- 330p, 330βpF
- Across both 220 kΞ©, carrying the treble past the filter.
- 1M, 1βMΞ©
- From the Reverb channelβs tone node to the Reverb pot. Only the Reverb channel feeds the springs.
- Reverb, 500βkΞ© pot, audio taper
- Reverb, 500 kΞ© audio. Its wiper is V2aβs grid, so it sets how hard the springs are driven.
- V2a, 12AU7 / ECC82
- One half of V2, a 12AU7, the reverbβs first gain stage.
- 100k, 100βkΞ©
- Plate resistor for V2a, +97 V on the drawing.
- 3.3k, 3.3βkΞ©
- Cathode resistor for V2a, +4.4 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V2aβs cathode. Its value isnβt printed on the drawing, so 20 Β΅F is assumed.
- .0047Β΅, 4.7βnF
- Coupling cap to the reverb driver. Into 220 kΞ© it cuts below about 150 Hz, so the springs get little bass.
- 220k, 220βkΞ©
- The reverb driverβs grid resistor.
- V2b, 12AU7 / ECC82
- The other half of V2, the reverb driver. Its cathode resistor isnβt bypassed. The drawing reads +9.2 V on it, about 9 mA.
- 1k, 1βkΞ©
- Cathode resistor for the reverb driver.
- T4, 10βkΞ© to 8βΞ©, 10βH primary, 50βmH leakage
- The reverb transformer, from the driverβs plate to the spring unit. The drawing reads 10 V across its primary. Its figures, 10 kΞ© into 8 Ξ©, are typical for the job.
- Unit in R, 800βmΞ©
- Resistance of the reverb unitβs input coil. The current through it drives the springs, which play from a measured tankβs impulse response, a recording of how the real springs ring after a click.
- Unit in L, 1.1βmH
- Inductance of the reverb unitβs input coil, a measured long tankβs figure.
- Unit out L, 350βmH
- The reverb unitβs output coil, 0.35 H, from V3aβs grid to ground. The springs come back in series with it.
- Unit out R, 181βΞ©
- Resistance of the unitβs output coil, 181 Ξ©, a measured long tankβs figure.
- 220k, 220βkΞ©
- Grid resistor for the reverb recovery stage.
- .001Β΅, 1βnF
- From the recovery grid to ground. It trims the springsβ highest treble.
- V3a, 6EU7
- One half of V3, a 6EU7, the reverb recovery stage. Its cathode isnβt bypassed.
- 100k, 100βkΞ©
- Plate resistor for V3a, +150 V on the drawing.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V3a, +1.2 V on the drawing.
- .0047Β΅, 4.7βnF
- Coupling cap from the recovery stage.
- 470k, 470βkΞ©
- From the recovery stage into V4aβs grid, where the reverb meets the Reverb channelβs dry signal.
- 150k, 150βkΞ©
- Plate resistor for the oscillator, from the +146 V node. The drawing reads +76 V on the plate.
- V3b, 6EU7
- The other half of V3, the tremolo oscillator. Its cathode goes straight to ground.
- .022Β΅, 22βnF
- First cap of the oscillatorβs phase-shift ladder.
- 390k, 390βkΞ©
- The ladderβs first leg to ground.
- .022Β΅, 22βnF
- Second ladder cap.
- 100k, 100βkΞ©
- In series with the Frequency pot, the ladderβs second leg. It sets the top speed.
- Frequency, 1.5βMΞ© pot, reverse audio taper
- Frequency, 1.5 MΞ© reverse audio, as a variable resistor from the 100 kΞ© to the foot switch. Turned up, its resistance drops and the oscillator runs faster.
- .01Β΅, 10βnF
- Third ladder cap, into the grid. At one frequency the three caps and legs turn the plateβs swing upside down by the time it reaches the grid, so the stage oscillates at that frequency.
- 4.7M, 4.7βMΞ©
- Grid leak for the oscillator, and the ladderβs last leg.
- .022Β΅, 22βnF
- Couples the oscillatorβs swing toward the Depth pot.
- 470k, 470βkΞ©
- In series with the Depth pot. With the pot it divides the oscillatorβs swing down.
- Depth, 250βkΞ© pot, audio taper
- Depth, 250 kΞ© audio, to ground. Its wiper is the lamp driverβs grid, so it sets how far the lampβs current swings.
- V5b, 12AU7 / ECC82
- The other half of V5 (V5a is the driver in the power amp), the lamp driver. Its plate current runs through the lamp, so the lamp brightens and dims with the oscillator.
- 500Ξ©, 500βΞ© pot, linear taper
- A 500 Ξ© wire-wound trim as a variable resistor in the lamp driverβs cathode. It sets the lampβs idle current. The drawing reads +2.06 V on the cathode. Its setting isnβt on the drawing, so itβs set near that voltage.
- Lamp, 24 V bulb, 18 mA
- The bulb in the photocell assembly Z1, from the +146 V node to the lamp driverβs plate. The drawing reads 10 V across it at idle. It glows dimly at idle and brightens as the driverβs current rises.
- Cell, Gibson LDR-500 cell
- The photocell in Z1, from the .022 Β΅F to ground. Lit, its resistance drops and it pulls V4aβs grid down, so the Reverb channel and its reverb get quieter. Dark, itβs about 1 MΞ© and hardly loads the grid.
- .022Β΅, 22βnF
- From V4aβs grid to the photocell. It keeps the gridβs DC off the cell.
- V5a, 12AU7 / ECC82
- 12AU7 (ECC82), the driver. Its plate current runs through the driver transformerβs primary, and the transformer splits the signal for the two output grids, so thereβs no phase inverter tube. Its grid connects straight to the preampβs output with no coupling cap, so its path to ground is through the preampβs volume and tone network.
- 1k, 1βkΞ©
- Cathode resistor for the driver. It sets the driverβs bias and its current, which also runs through the transformerβs primary.
- 5Β΅, 5βΒ΅F electrolytic
- Bypass cap across the driverβs cathode resistor, for full gain above a few hertz.
- T3, 10βkΞ© to 40βkΞ©, 15βH primary, 30βmH leakage
- The driver transformer, from the driverβs plate to the supply. Its secondary is center-tapped: one end drives tube Aβs grid, the other tube Bβs, in opposite phase, and the tap goes to ground, so each gridβs DC path is the winding itself. With no coupling caps the grids canβt charge up and block on a hard note the way cap-coupled grids do. Each half of the secondary has about 1 times the primaryβs turns. Its primaryβs 720 Ξ© is from the drawingβs voltages. The 1:1 ratio, 15 H primary and the rest are typical of a small driver transformer.
- V6, EL84 / 6BQ5 (Philips curves)
- EL84, tube A of the push-pull pair, its cathode on the shared cathode resistor, so it biases itself.
- V7, EL84 / 6BQ5 (Philips curves)
- EL84, tube B of the pair.
- 130, 130βΞ©
- The shared cathode resistor. Every output tubeβs current runs through it and lifts the cathodes above the grids, and thatβs the bias. Driven hard, the pair draws more current on average, so the cathodes climb and the tubes run colder, which softens the clipping.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signalβs frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 3 H, 3βH
- A choke from B+ to the screen supply, as in the amp this style is based on. It passes DC with little drop, so the screens sit close to B+. With the cap after it, it would filter ripple, but ripple isnβt modeled here. Typical of the part.
- 400, 400βΞ©
- The chokeβs winding resistance, typical. Itβs all the DC drop the screens see from B+.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap on the screen supply.
- 1k, 1βkΞ©
- Dropping resistor from the screen supply node to the node for the driver and the reverb driver, as on the Gibson GA-20RVT Minuteman drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the driver and the reverb driver. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 4.7k, 4.7βkΞ©
- Dropping resistor from the node for the driver and the reverb driver to the node for the preamp, as on the Gibson GA-20RVT Minuteman drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 10k, 10βkΞ©
- Dropping resistor from the node for the driver and the reverb driver to the node for the tremolo, as on the Gibson GA-20RVT Minuteman drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the tremolo. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 8βkΞ© to 8βΞ©, 40βH primary, 10βmH leakage
- The output transformer, 8 kΞ© plate to plate into 8 Ξ©, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 250 V ac, 60 Hz
- One half of the power transformerβs high-voltage winding, 250 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 250 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 130βΞ©
- Resistance of one half of the winding, plus the primaryβs share. With the rectifierβs own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 130βΞ©
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 20Β΅, 20βΒ΅F electrolytic
- The reservoir cap. It feeds the output transformerβs center tap. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 8.69βΞ©
- Voice coil resistance, the floor of the speakerβs impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ξ© peak near 74 Hz on 8 Ξ©), scaled to the 8 Ξ© tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256βΒ΅H
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 464βΒ΅H
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3βΞ©
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13βmH
- A second step in the treble rise, with Loss R2 across it: a real voice coilβs losses keep climbing from a few hundred hertz.
- Loss R2, 2.19βΞ©
- Limits what Loss L2 adds.
- Tank R, 83.7βΞ©
- Height of the bass resonance, about 92 Ξ© in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 21.1βmH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220βΒ΅F
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The 6EU7 model is fitted to the Tung-Sol reissue plate chart. The 12AU7s use the 12AU7 model. The photocell and its bulb are the benchβs Gibson LDR-500. The reverb transformer and unit are typical, not on the drawing.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.