Op-amp overdrive with a mid boost after the clipper, 1979 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Ibanez STL Super Tube.
An op-amp input buffer, a Tube Screamer style clipper, then a mid boost whose frequency Bite moves, then the Tube Screamer tone stage. Two NJM4558Ds.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The clipper is the Tube Screamerβs: 1 plus 51 kΞ© and the Drive pot over 4.7 kΞ©, with full gain only above about 720 Hz, and two silicon diodes across the feedback. IC1A then lifts a band of mids by about 7 dB. Bite moves that band from about 200 Hz to about 2.5 kHz. The boost comes after the clipping here, so it shapes the clipped sound like an EQ and doesnβt change how hard the diodes clip. The ST-9 puts the same stage before the clipper. Bright works as a Tube Screamerβs Tone. The model leaves out the bypass switching.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R32, 10βkΞ©
- Top of the 4.5 V reference divider.
- R33, 10βkΞ©
- Bottom of the reference divider.
- C16, 47βΒ΅F electrolytic
- Filters the 4.5 V reference.
- C1, 47βnF
- Input coupling cap.
- R1, 1βkΞ©
- Input series resistor.
- R2, 510βkΞ©
- Biases the input buffer at 4.5 V and sets the input impedance near 510 kΞ©.
- IC1B, JRC4558D
- Input buffer, an op-amp follower with a gain of one.
- C2, 1βΒ΅F
- Coupling cap into the clipper, non-polarized.
- R3, 10βkΞ©
- Biases the clipperβs plus input at 4.5 V.
- IC2A, JRC4558D
- The clipper, as in a Tube Screamer: a non-inverting stage with diodes across its feedback.
- C6, 47βnF
- In series with R7 to ground, so the clipper has full gain only above about 720 Hz.
- R7, 4.7βkΞ©
- Sets the gain with R8 and Drive: 1 + (51 k + Drive) / 4.7 k.
- R8, 51βkΞ©
- Least feedback resistance, so the gain stays over about 12.
- Drive, 500βkΞ© pot, audio taper
- Drive, a 500 kΞ© audio pot used as a variable resistor in the feedback.
- C5, 51βpF
- Across the feedback. It rolls off the top of the clipped signal.
- D1, D2, 1N914 / 1N4148, one each way
- Two 1S1588 silicon diodes, one each way across the feedback, modeled as 1N914s.
- C4, 1βΒ΅F
- Coupling cap into the mid stage, non-polarized.
- R6, 220βkΞ©
- Biases the mid stageβs plus input at 4.5 V.
- IC1A, JRC4558D
- The mid stage. Its gain is one at the bass and treble and rises around the Bite frequency.
- C3, 27βnF
- From the mid stageβs output to its minus input. With C19 it sets how high the boost goes and how wide it is.
- R5, 1.5βkΞ©
- From the output toward the Bite common point.
- Bite, 20βkΞ© pot, reverse audio taper
- Bite, one half of a dual 20 kΞ© reverse audio pot, used as a variable resistor. Turned up, both halves drop in resistance and the boost moves up in frequency.
- R4, 1.5βkΞ©
- From the minus input toward the Bite common point.
- Bite (second half), 20βkΞ© pot, reverse audio taper
- The other half of Bite, turned by the same knob.
- C19, 68βnF
- From the Bite common point to ground. Around the Bite frequency it pulls the feedback down, so the gain rises there.
- R9, 1βkΞ©
- With C7, a low-pass ahead of the tone stage, about 1.6 kHz.
- C7, 100βnF
- The low-pass cap.
- R10, 10βkΞ©
- Biases the tone stageβs plus input.
- IC2B, JRC4558D
- Tone stage.
- Bright, 20βkΞ© pot, linear taper
- Bright, 20 kΞ©. It slides R34 and C20 from the plus input, where they cut treble, to the minus input, where they lift it. The drawing marks it β20K(G)β. Linear is assumed.
- C20, 220βnF electrolytic
- Tone network cap, a tantalum.
- R34, 220βΞ©
- Tone network resistor.
- R11, 1βkΞ©
- Tone stage feedback resistor.
- C8, 1βΒ΅F
- Coupling cap toward Level, non-polarized.
- R12, 1βkΞ©
- Series resistor to Level.
- Level, 100βkΞ© pot, linear taper
- Level, a 100 kΞ© linear pot. Its bottom lug goes to the 4.5 V reference, so the wiper sits at 4.5 V for the JFET switch after it.
- R19, 510βkΞ©
- Biases the JFET switchesβ joined side at 4.5 V. The effect pathβs switch is drawn as a wire.
- C10, 100βnF
- Coupling cap into the output buffer.
- R14, 510βkΞ©
- Biases the output buffer from the 4.5 V reference.
- Tr1, 2SC1815
- Output buffer, an emitter follower.
- R13, 10βkΞ©
- Output buffer emitter resistor.
- C11, 10βΒ΅F electrolytic
- Output coupling cap.
- R16, 10βkΞ©
- Holds the output side of C11 at ground.
- R17, 470βΞ©
- Output series resistor.
About this version
- STL
- Values from the factory drawing. NJM4558D op-amps. The 2SC2458GR output buffer uses the 2SC1815 model.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.