Photocell state-variable envelope filter, 1972 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Musitronics Mu-Tron III.
An envelope filter on ±9 V. The guitar’s peaks light an LED in a sealed module, and its two photocells move a three-op-amp state-variable filter. Gain sets how hard you have to play, Peak how sharp the filter is, and the switches set the mode, the range and which way it sweeps.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for A1 amplifies the guitar by 0.12 to 36, set by Gain. Its output feeds the filter and the envelope. The filter is A2, A3 and A4 in a loop. A2’s output is high-pass, A3’s band-pass and A4’s low-pass, and Mode selects one. Each photocell sits across a 220 kΩ integrator resistor, so more light means a higher filter frequency. Peak sets how much band-pass returns to A2. At 0 the peak is about 3 times A1’s output, and at full about 34 times. The envelope side rectifies A1’s output into C9. In Up, A6 sets the LED’s current at C9’s voltage over R23, so the filter rests low and rises as you pick. In Down the LED rests bright and dims as you pick. Range Low adds 2200 pF to each integrator and drops the whole sweep to under half. The module’s cells and R23 are assumed.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- −9 V, -9 V
- The second 9 V battery, the −9 V rail. It feeds R18 and the op-amps’ negative supply.
- Gain, 1 MΩ pot, reverse audio taper
- Gain, 1 MΩ reverse audio, a variable resistor in series with the input. Clockwise there is less resistance and more gain, about 0.12 at 0, 1.2 at the middle and 36 at full. It is also the pedal’s input impedance, 1 MΩ down to 3.3 kΩ.
- R1, 3.3 kΩ
- Sets the highest gain, 120 kΩ over 3.3 kΩ, 36.
- C1, 4.7 µF electrolytic
- Input coupling cap.
- R4, 120 kΩ
- A1’s feedback resistor.
- C3, 10 pF
- Across R4. It rolls A1 off above about 130 kHz and keeps it stable.
- R3, 120 kΩ
- Holds A1’s plus input at ground.
- C2, 100 nF
- Across R3, to keep noise off A1’s plus input.
- A1, RC4558
- Input amp, half a 4558, inverting. Its output feeds the filter, the envelope side and the footswitch’s bypass contact.
- R5, 4.7 kΩ
- Brings A1’s output to A2’s plus input.
- R9, 12 kΩ
- In series with Peak, from A2’s plus input to the band-pass. It sets how broad the filter can get.
- Peak, 150 kΩ pot, audio taper
- Peak, 150 kΩ audio, a variable resistor. Clockwise there is more resistance, so less band-pass returns to A2 and the peak grows sharper and taller. It is about 3 times A1’s output at 0, 6 at the middle and 34 at full.
- A2, RC4558
- The filter’s summing amp, half a 4558. Its output is the high-pass, which is twice its plus input minus the low-pass.
- R7, 22 kΩ
- A2’s feedback resistor.
- R8, 22 kΩ
- Brings the low-pass back to A2’s minus input, equal to R7.
- R10, 220 kΩ
- A3’s input resistor. With the cell dark it sets the lowest filter frequency, about 400 Hz on High.
- LDR1, Module cell
- One cell of the module, across R10. Lit, its resistance drops and the filter frequency rises. Its figures are assumed.
- C5, 1.8 nF
- A3’s integrating cap.
- C4, 2.2 nF
- Added to C5 by Range Low.
- A3, RC4558
- First integrator, half a 4558. Its output is the band-pass.
- R12, 220 kΩ
- A4’s input resistor, as R10.
- LDR2, Module cell
- The module’s other cell, across R12, lit by the same LED.
- C7, 1.8 nF
- A4’s integrating cap.
- C6, 2.2 nF
- Added to C7 by Range Low.
- A4, RC4558
- Second integrator, half a 4558. Its output is the low-pass.
- C10, 15 µF
- Output coupling cap, 15 µF non-polar.
- R25, 560 Ω
- In series with the output, about 600 Ω out with the op-amp.
- C8, 2.2 µF electrolytic
- Couples A1’s output to the envelope side.
- R14, 22 kΩ
- A5’s input resistor. With R16 the rectifier’s gain is 45.
- R24, 12 kΩ
- Beside R14 in Drive Down, raising the rectifier’s gain to 129.
- R15, 1 MΩ
- Holds A5’s plus input at ground.
- A5, RC4558
- The rectifier, half a 4558, inverting. On the guitar’s down swings it charges C9 through D2 to 45 times the swing. On the up swings D1 holds it.
- D1, 1N914 / 1N4148
- Catches A5’s output on the up swings, so it doesn’t run to the rail.
- D2, 1N914 / 1N4148
- Passes A5’s output to C9 on the down swings only.
- R16, 1 MΩ
- A5’s feedback, taken after D2 so the diode’s drop doesn’t count.
- R17, 330 Ω
- Charges C9. With C9 the attack is about 1.6 ms.
- C9, 4.7 µF electrolytic
- The envelope cap. R18 drains it toward −9 V, so it falls back to 0 V in about 0.1 s from 5 V.
- R18, 47 kΩ
- Drains C9 to the −9 V rail. A5 holds the bottom at 0 V.
- R19, 180 kΩ
- Top of the Down reference divider.
- R20, 120 kΩ
- Bottom of the divider. With R19 it sets 3.6 V for Drive Down.
- A6, RC4558
- The LED driver, half a 4558. It holds the LED’s cathode at C9’s voltage in Up, or at 7.2 V minus C9’s voltage in Down, so the LED’s current is that voltage over R23.
- R21, 120 kΩ
- From C9 to A6’s minus input.
- R22, 120 kΩ
- From the LED’s cathode to A6’s minus input, equal to R21.
- LED, Red LED
- The module’s LED. Its light follows its current, which is none at rest in Up and about 2 mA on a hard pick.
- R23, 3.3 kΩ
- Sets the LED’s current. The factory picked it to suit each module. 3.3 kΩ is assumed.
About this version
- Stock
- Two 9 V batteries, ±9 V. 4558 op-amps, one red LED lighting two photocells.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.