Variable-mu tube limiter, 1959 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Fairchild 660 Automatic Gain Control Amplifier.
Eight remote-cutoff triode sections, four a side, make one push-pull stage whose gain falls as their grids go negative. A separate amplifier ending in two 6V6s and a bridge rectifier makes that grid voltage, tens of volts of it, so the pull down is fast and the push-pull pair cancels its thump.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar reaches the unit through a DI box and line amp (20 dB), which arenβt part of it. Input gain feeds T1, which steps the signal up about 9.6 times and splits it at its center tap, so four 6386 sections on one side and four on the other are driven in opposite phase. The center tap carries the control voltage, 0 V at rest. The 6386 is a remote-cutoff triode: as its grid goes more negative its gain falls smoothly, and the push-pull pair cancels the thump of that change while the signal adds. T2 steps the plates down into the 600 Ξ© line, about 6 dB of gain with Input gain full. The sidechain listens to the output through T7. V5 sits just past cutoff, and DC threshold sets how far past, so it passes only the peaks that rise above that. V6 and the two 6V6s build those peaks up, T3 steps them down, and the bridge rectifies them into tens of volts on the control line, so the pull down comes within a few milliseconds. Threshold sets how much of the output reaches V5. Time constant sets how fast the control line lets go, from about 0.1 s in position 1 to about 1.8 s in position 4. Positions 5 and 6 add a slower capacitor that only fills on a long loud passage. With both thresholds at their most sensitive, the output stops rising near +3 dBm.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- DI in, 1βMΞ©
- Not part of the unit: the DI boxβs input resistance, 1 MΞ©, as a guitar ampβs.
- DI box, 10 V
- Not part of the unit: a DI box with a line amp behind it, 20 dB of gain and a 50 Ξ© output, as a guitar would be brought up to line level in a studio before a limiter. The unit itself has only about 6 dB of gain, so a guitar at its own level barely reaches its threshold.
- Input gain, 600βΞ© pot, audio taper
- AT-1, Input gain. On the real unit itβs a 600 Ξ© step attenuator, 1 dB a step. Here itβs a 600 Ξ© audio-taper pot. It sets how hard the signal drives the 6386s, so with the thresholds fixed it sets how much the unit limits.
- T1, 600βΞ© to 55.3βkΞ©, 4βH primary, 3βmH leakage
- The input transformer, a UTC Y-6431: 600 Ξ© to 55 kΞ©, 1:9.6, so the signal comes out about 9.6 times larger across the whole secondary. Each half feeds one sideβs four grids, in opposite phase. The center tap carries the control voltage to all eight. Tap any piece of it to change its figures.
- R1, 100βkΞ©
- R1, 100 k 1 %, across one half of T1βs secondary. It loads the transformer so its response stays flat.
- R2, 100βkΞ©
- R2, 100 k 1 %, across the other half.
- V1a, V2a, V3b, V4b, 6386
- Four 6386 sections in parallel, drawn as one: side A of the push-pull stage. The 6386 is a remote-cutoff triode, its grid wound unevenly, so as the control voltage goes more negative its gain falls smoothly instead of cutting off. This is the gain cell.
- V1b, V2b, V3a, V4a, 6386
- The other four sections, side B, driven in opposite phase. The control voltage moves all eight grids together, so the thump of the gain change cancels in the push-pull pair while the signal adds.
- Balance, 500βΞ© pot, linear taper
- R3-A, Balance, 500 Ξ© from cathode bus A to bus B, a front-panel screwdriver control ganged with R3-B. It shifts current from one side to the other, so the two sides can be matched and the control voltageβs thump cancels. Taper assumed linear.
- Balance (B), 500βΞ© pot, linear taper
- R3-B, the other half of the ganged Balance control, also from bus A to bus B.
- R4, 1.8βkΞ©
- R4, 1,800 Ξ© 1 W, from R3-Aβs wiper to ground. With R5 it sets the eight sectionsβ current.
- R5, 1.8βkΞ©
- R5, 1,800 Ξ© 1 W, from R3-Bβs wiper to ground.
- C2, 680βpF
- C2, 680 pF, from cathode bus A to ground. Far too small to bypass the cathodes at audio frequencies.
- C1, 680βpF
- C1, 680 pF, from cathode bus B to ground.
- T2, 1.5βkΞ© to 600βΞ©, 20βH primary, 4βmH leakage
- The output transformer, about 1.6:1, so the 600 Ξ© line looks like 1.5 kΞ© plate to plate. The drawing lists no figures for it. This load is chosen so the meter follows the gain reduction, as the real unitsβ meters do: against a load this light the 6386sβ gain falls with their current. Against the 48.6 kΞ© of the replacement transformers made for these units, the gain hardly moved while the current fell, and the meterβs 10 to 20 dB marks crowded into the bottom of the scale. Its two secondaries are in series. Tap any piece of it to change its figures.
- R56, 33βΞ©
- A 33 Ξ© resistor from the regulated line to the meter shuntsβ joint (labeled R56 on the drawing, the same as the 1,200 Ξ© on T7).
- R6, 30βΞ©
- R6, 30 Ξ© 1 %, carries the upper halfβs plate current from the joint to T2 (pin 3). The meter reads the voltage across it.
- R7, 30βΞ©
- R7, 30 Ξ© 1 %, the same for the lower half (T2 pin 2).
- R57, 2.5βkΞ©
- R57, 2,500 Ξ© 1 %, in series with the meter.
- M1, 1βkΞ©
- M1, the meter: a plain moving-coil movement with no rectifier, 1 kΞ© and 150 Β΅A full scale (typical, not on the drawing). In Zero it reads the eight 6386sβ plate current: full current with no compression, less as the control line pulls the grids down. At rest it carries 111 Β΅A, the 0 mark. On the unit, the regulated lineβs Zero control (R41) puts the needle there. The face is printed in dB of compression, each mark at the current measured at that much compression: 2 dB at 82 Β΅A, 4 dB at 59, 6 dB at 39, 10 dB at 20. Past about 10 dB the signalβs own swing holds the average current up, so 15 and 20 dB sit close together near the bottom.
- Line, 600βΞ©
- Not part of the unit: the 600 Ξ© line it drives.
- R55, 330βΞ©
- R55, 330 Ξ©, from one output line to T7. The sidechain listens to the output, so it limits what it has already turned down (feedback limiting).
- R54, 330βΞ©
- R54, 330 Ξ©, from the other output line (grounded here) to T7.
- R56, 1.2βkΞ©
- R56, 1,200 Ξ©, across T7βs primary.
- T7, 600βΞ© to 173βkΞ©, 10βH primary, 3βmH leakage
- The sidechainβs input transformer, 1:17, its center tap grounded, so each half drives one grid of V5 in opposite phase. The secondaryβs own resistance is left out (the tap is grounded straight). Tap any piece of it to change its figures.
- R8, 24βkΞ©
- R8, 24 k 5 %, loads one half of T7βs secondary.
- R9, 24βkΞ©
- R9, 24 k 5 %, loads the other half.
- Threshold, 180βkΞ© pot, audio taper
- R10-A, Threshold, 180 k across one half of T7βs secondary, wiper to V5aβs grid, ganged with R10-B. Turned up, more of the output reaches the sidechain, so limiting starts at a lower output level. Taper assumed audio.
- Threshold (B), 180βkΞ© pot, audio taper
- R10-B, the other half of the ganged Threshold, across the other half of the secondary, wiper to V5bβs grid.
- V5a, 12AX7 / ECC83 / 7025
- Half a 12AX7, the sidechainβs first stage, one side of a push-pull pair.
- V5b, 12AX7 / ECC83 / 7025
- The other half of the 12AX7, in opposite phase.
- R13, 1βMΞ©
- R13, 1 M from the regulated line to V5βs cathodes, part of their bias.
- R14, 18βkΞ©
- R14, 18 k, V5βs cathode resistor.
- DC threshold, 100βkΞ© pot, linear taper
- R12, DC threshold, 100 k from V5βs cathodes to ground, a front-panel screwdriver control. Its wiper takes current from the regulated line through R11. Turned toward the cathode end it lifts the cathodes, biasing V5 toward cutoff, so the sidechain needs more signal before it acts. Taper assumed linear.
- R11, 40βkΞ©
- R11, 1 W, from the regulated line to DC thresholdβs wiper. Its first digit is unclear on the drawing. Itβs read as 40 k, since 10 k would put several watts into a 1 W part.
- R15, 100βkΞ©
- R15, 100 k 1 W, V5aβs plate resistor.
- R16, 100βkΞ©
- R16, 100 k 1 W, V5bβs plate resistor.
- C3, 50βnF
- C3, .05 Β΅F, V5aβs plate to V6aβs grid.
- C4, 50βnF
- C4, .05 Β΅F, V5bβs plate to V6bβs grid.
- R17, 1βMΞ©
- R17, 1 M, V6aβs grid resistor.
- R18, 1βMΞ©
- R18, 1 M, V6bβs grid resistor.
- V6a, 12BH7 (GE, JJ)
- Half a 12BH7A, the driver for V7.
- V6b, 12BH7 (GE, JJ)
- The other half of the 12BH7A, the driver for V8.
- R19, 100βkΞ©
- R19, 100 k 2 W, V6aβs plate resistor, from the raw line.
- R22, 100βkΞ©
- R22, 100 k 2 W, V6bβs plate resistor.
- R20, 1βkΞ©
- R20, 1,000 Ξ© 1 W, V6aβs cathode resistor, unbypassed.
- R21, 1βkΞ©
- R21, 1,000 Ξ© 1 W, V6bβs cathode resistor.
- R23, 2.7βkΞ©
- R23, 2,700 Ξ© 1 W 5 %, from V6aβs cathode to one end of T3βs feedback winding: negative feedback around the 6V6s and their transformer.
- R24, 2.7βkΞ©
- R24, 2,700 Ξ©, from V6bβs cathode to the other end of the feedback winding.
- R29, 560βΞ©
- R29, 560 Ξ© 1 W, loads one end of the feedback winding to ground.
- R30, 560βΞ©
- R30, 560 Ξ© 1 W, loads the other end.
- C5, 100βnF
- C5, from V6aβs plate to V7βs grid. Its value isnβt legible on the drawing, so itβs .1 Β΅F, as C6.
- C6, 100βnF
- C6, .1 Β΅F, from V6bβs plate to V8βs grid.
- R25, 330βkΞ©
- R25, 330 k, V7βs grid resistor, to its grounded cathode: no grid bias.
- R26, 330βkΞ©
- R26, 330 k, V8βs grid resistor.
- V7, 6V6GT
- A 6V6GT, one side of the sidechainβs push-pull output. Its cathode is grounded and its grid sits at 0 V, so its screen supply sets its current.
- V8, 6V6GT
- The other 6V6GT.
- R27, 560βΞ©
- R27, 560 Ξ©, V7βs screen resistor, from the lower rail.
- R28, 560βΞ©
- R28, 560 Ξ©, V8βs screen resistor.
- R59, 47βkΞ©
- R59, 47 k, with C19 from V7βs plate back to its own grid: it cuts V7βs gain at the very top so the sidechain stays stable.
- C19, 20βpF
- C19, 20 pF 1.6 kV, in series with R59.
- R60, 47βkΞ©
- R60, 47 k, with C20 from V8βs plate to its grid.
- C20, 20βpF
- C20, 20 pF 1.6 kV, in series with R60.
- T3 pri A, 5βH
- T3βs primary, V7βs half, from BL to F. With the other half, 10 kΞ© plate to plate.
- T3 pri B, 5βH
- T3βs primary, V8βs half, from R to BR.
- T3 sec, 1.25βH
- T3βs secondary, a quarter of the primaryβs turns, into the bridge.
- T3 fb, 222βmH
- T3βs feedback winding, about a tenth of the primaryβs turns (9.5:1), back to V6βs cathodes.
- T3 k, coupling factor 0.9990
- Coupling between T3βs two primary halves.
- T3 k, coupling factor 0.9990
- Coupling between T3βs primary and secondary. Below 1, the part that misses acts as leakage inductance.
- T3 k, coupling factor 0.9990
- Coupling between T3βs other primary half and the secondary.
- T3 k, coupling factor 0.9990
- Coupling between T3βs primary and its feedback winding.
- T3 k, coupling factor 0.9990
- Coupling between T3βs other primary half and the feedback winding.
- T3 k, coupling factor 0.9990
- Coupling between T3βs secondary and its feedback winding.
- R31, 3.9βkΞ©
- R31, 3,900 Ξ© 1 W, across T3βs secondary.
- CR, 1N4001
- One diode of the bridge CR. Its plus corner is grounded, so the bridgeβs minus pulls the control line negative on both halves of the wave.
- CR, 1N4001
- The bridgeβs second diode to the grounded corner.
- CR, 1N4001
- One of the bridgeβs two diodes to its minus corner, the control line.
- CR, 1N4001
- The other diode to the control line.
- C7, 2βΒ΅F
- C7, 2 Β΅F, holds the control voltage in every position of S2.
- R32, 220βkΞ©
- R32, 220 k, lets the control line go back to 0 V in every position.
- R37, 68βkΞ©
- R37, 68 k, on the control line in position 1 only: about 0.1 s.
- R33, 470βkΞ©
- R33, 470 k, on the control line in position 2: about 0.3 s.
- C11, 2βΒ΅F
- C11, 2 Β΅F, joins C7 in positions 3 to 5.
- C9, 4βΒ΅F
- C9, 4 Β΅F, joins in position 4.
- R34, 100βkΞ©
- R34, 100 k, in series with C8 in positions 5 and 6. C8 charges only on a long run of loud playing, then holds the release back.
- C8, 8βΒ΅F
- C8, 8 Β΅F, the slower time constant of positions 5 and 6.
- R35, 100βkΞ©
- R35, 100 k, in series with C10 in position 6.
- C10, 20βΒ΅F
- C10, 20 Β΅F, the slowest time constant, position 6 only.
- Regulated line, 240 V
- Stands in for the regulator (6BL7, 6084, 5651) as a steady 240 V. The drawing prints no voltage. 240 V is what the 670βs manual lists for its own regulated line, and it sits inside the Zero controlβs range here.
- C12-A, 80βΒ΅F electrolytic
- C12-A, 80 Β΅F 450 V, on the regulated line.
- Raw line, 358 V
- Stands in for the GZ34 rectifier and L1 as a steady source behind 300 Ξ©, so the raw line, the regulatorβs input, sits near 340 V with the sidechainβs load on it. The drawing prints no voltage. Itβs set for the 6BL7βs drop above the regulated line.
- C13, C18, 70βΒ΅F electrolytic
- C13 and C18, 140 Β΅F 350 V each, in series on the raw line, so they act as 70 Β΅F.
- R38, 27βkΞ©
- R38, 27 k 1 W, from the regulated line to the lower rail. It holds the 6V6sβ screen current down.
- R39, 100βkΞ©
- R39, 100 k 1 W, the lower railβs bleeder.
- C12-B, 60βΒ΅F electrolytic
- C12-B, 60 Β΅F 350 V, on the lower rail.
About this version
- As drawn
- The factory drawing of the Model 660, fed unbalanced and loaded with 600 Ξ©.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.