Teisco Check Mate 20 tone stack
Tone stacks and tone controls from amps and pedals, from their schematics, with the stage that drives each one and what it feeds. Turn the knobs and watch the curve. Pin a setting to compare, change any part, and listen through a speaker. Pickups and guitar knobs are on the Guitars page.
The Treble and Bass controls of the Teisco Check Mate 20, with every part as on the bench.
Swipe sideways for the whole drawing. Tap a part to change it. The source drives the end marked in, and the load hangs on the end marked out.
At this setting
0 dB is the source’s voltage with nothing hooked to it, so the curve shows what the stack cuts. A tube source changes the curve only through its output resistance, not its gain.
Pin this curve keeps what the graph shows, up to three pins in their own colors. Pins stay when you switch stacks, so you can lay a Marshall treble sweep over a Vox one. In a sweep, the lightest line is the knob at 0 and the darkest is 10.
Listen
You hear a picked string through a guitar on full, with 15 feet of cable. Play without it leaves the stack out.
Source and load
Driven by
Driving
The knobs
- Treble
- Treble, 1 MΩ. Its wiper is the network’s output. Turned up, the wiper nears the 500 pF and more treble gets through. Turned down, it nears the .002 µF to ground. Marked B, read as linear. Brighter clockwise is assumed.
- Bass
- Bass, 1 MΩ, between the .001 µF and the .03 µF. Turned up, the wiper nears the top, the .03 µF passes the lows to the wiper and the .001 µF is shorted out. Marked B, read as linear. More bass clockwise is assumed.
Parts
- 50 nF
- Coupling cap into the tone network.
- 500 pF
- Treble cap, 500 pF to the Treble pot’s top.
- Treble 1M
- 1 MΩ, Treble, 1 MΩ. Its wiper is the network’s output. Turned up, the wiper nears the 500 pF and more treble gets through. Turned down, it nears the .002 µF to ground. Marked B, read as linear. Brighter clockwise is assumed.
- 2 nF
- From the Treble pot’s bottom to ground.
- 100 kΩ
- Into the bass side of the network, 100 kΩ to the Bass pot’s top.
- Bass 1M
- 1 MΩ, Bass, 1 MΩ, between the .001 µF and the .03 µF. Turned up, the wiper nears the top, the .03 µF passes the lows to the wiper and the .001 µF is shorted out. Marked B, read as linear. More bass clockwise is assumed.
- 1 nF
- From the Bass pot’s top to its wiper.
- 30 nF
- From the Bass pot’s bottom to its wiper.
- 5 kΩ
- The bottom of the bass side, 5 kΩ to ground.
- 100 kΩ
- From the Bass wiper to the network’s output, where the bass and treble sides mix.
Source and load
Source: 60 kΩ, the output resistance of the stage before it on the bench at 1 kHz. Load: 390 kΩ with 7.7 pF across it, the input of what follows it on the bench, from its impedance at 1 and 10 kHz.
Values, wiring and drawing are taken from the Teisco Check Mate 20 on the bench, so the two always match.
How a tone stack works
Two ways through In the FMV stack the treble cap is small, so it passes only the highs, straight to the top of the treble pot. Everything else goes through the slope resistor, then the bass and mid caps. The bass cap feeds the bottom of the treble pot, and the bass pot sits between there and the top of the mid pot. Turned down, it shorts the bass cap’s end toward the mid pot, and the lows drop away. The mid pot sits between the mid cap and ground, so turning it up lifts the whole lower path off ground. The output is the treble pot’s wiper, a mix of the highs at the top of its track and the lows and mids at the bottom.
The mid scoop Where a stack passes the bass and the treble by different paths, there’s a stretch in between where neither path passes much. That dip in the mids is the scoop. Its depth and center move with the knobs. In the FMV stack the slope resistor and treble cap set where it sits, and the mid knob fills it in. A plain low-pass or high-pass filter has no scoop.
Warnings The summary above the graph turns red if the stack can’t be solved as set, usually from a part at zero or a shorted pot track.